(a)
Make sure the EICAS message NOSE GEAR DOWN shows on the bottom display.
S 495-136
(50)
Install a deactuator on the sensor S10079.
S 865-137
(51)
Erase the EICAS ECS/MSG AUTO EVENT page.
S 735-138
(52)
Make sure the EICAS message LDG GEAR MONITOR is not shown on the bottom display.
S 495-139
(53)
Install a deactuator on the sensor S10065.
S 735-140
(54)
Make sure the green NOSE light is off. Make sure the EICAS message LDG GEAR MONITOR is shown on the bottom display after 2 seconds.
(a)
Make sure the EICAS message NOSE GEAR LOCKED shows on the bottom display.
S 735-141
(55)
Move the COMPUTER switch to the L position. Make sure the EICAS message LDG GEAR MONITOR is shown on the bottom display.
(a)
Make sure the EICAS message NOSE GEAR LOCKED shows on the bottom display.
S 495-142
(56)
Install a deactuator on the sensor S10078.
S 735-143
(57)
Make sure the indications that follow occur:
(a)
The amber DOORS and GEAR lights are on.
(b)
The green NOSE, RIGHT and LEFT lights are off.
(58)
Install an actuator on the sensor S10081.
(59)
Erase the EICAS ECS/MSG AUTO EVENT page.
S 735-146
(60)
Make sure the conditions that follow occur:
(a)
The amber DOORS light is off.
(b)
The EICAS message GEAR DOORS is not shown on the top display after 35 seconds.
S 495-144
S 865-145
32-61-00
ALL ú ú 01 Page 530 ú Sep 20/96
A
757
MAINTENANCE MANUAL
S 735-147
(61)
Make sure the EICAS message PSEU BITE is shown on the bottom display after 10 seconds.
S 735-148
(62)
Move the COMPUTER switch to the R position. Make sure the EICAS message PSEU BITE is shown on the bottom display.
S 735-149
(63)
Move the control lever for the landing gear to the DN position. Make sure the EICAS message LDG GEAR MONITOR is shown on the bottom display after 60 seconds.
S 215-215
(64)
Make sure the EICAS message GEAR LEVER shows on the bottom display.
S 735-150
(65)
Move the COMPUTER switch to the L position. Make sure the EICAS message LDG GEAR MONITOR is shown on the bottom display.
S 215-216
(66)
Make sure the EICAS message GEAR LEVER shows on the bottom display.
S 495-189
(67)
Make sure the downlocks are installed on the nose and main landing gear (AMM 32-00-20/201) and the chocks are put on the wheels.
S 865-151
(68)
Make sure the pressure is removed from the left hydraulic system (AMM 29-11-00/201).
S 865-152
(69)
Use the OVRD button and and move the control lever for the landing gear to the UP position.
S 735-153
(70)
Erase the EICAS ECS/MSG AUTO EVENT page.
S 865-154
(71)
Make sure the EICAS message LDG GEAR MONITOR is not shown on the bottom display.
WARNING:_______ MAKE SURE THE DOWLOCKS ARE INSTALLED ON THE NOSE AND MAIN
LANDING GEAR BEFORE YOU MOVE THE CONTROL LEVER FOR THE LANDING
GEAR. IF THE LEVER IS MOVED WITHOUT THE DOWNLOCKS INSTALLED,
THE LANDING GEAR CAN RETRACT AND CAUSE INJURY TO PERSONS OR
DAMAGE TO EQUIPMENT.
32-61-00
ALL ú ú 01 Page 531 ú Jan 28/02
A
757
MAINTENANCE MANUAL
S 865-155
(72)
Move the control lever for the landing gear to the DN position.
S 095-156
(73)
Remove the actuators or deactuators on the sensors in the list
below:
SENSOR______ ACTUATOR________ DEACTUATOR__________
S10057 -- Remove
S10061 -- Remove
S10065 -- Remove
S10066 -- Remove
S10070 -- Remove
S10072 Remove --
S10074 -- Remove
S10078 -- Remove
S10079 -- Remove
S10076 Remove --
S10081 Remove --
S10241 Remove --
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：757 AMM 飞机维护手册 起落架 CHAPTER 32 - LANDING GEAR 3(155)
