(2)
The AUTO APP mode provides for automatic capture of the localizer and glide slope beams from other lateral or vertical modes. When switching to the AUTO APP mode from the VOR/LOC mode after localizer beam capture, the GS arm (amber) indicator illuminates at the annunciator if a "GS flag" signal is generated by the GS receiver and a "LOC freq" select signal is initiated by the VOR/LOC receiver. When the center of the glide slope beam is intercepted, a "GS capture" signal is generated in the GS beam sensor and the computer is automatically switched to the final approach phase. The COMPUTER warning flag at this time begins monitoring glide slope information in addition to its other inputs. At this time also, the GS (green) indicator illuminates in the annunciator.
(3)
In the final approach phase, the bank channel utilizes the same signals as described for VOR/LOC mode and the roll commands are limited to 15 degrees. After glide slope capture the localizer deviation pointer comes into view in the HSI and indicates deviation from the localizer beam at approximately twice the sensitivity of the HSI bar. The complementary filter provides for cross wind correction. Its output is combined with the localizer deviation signal to provide a damping signal. The difference between these two signals becomes the bank command signal. The bank command signal is then mixed with the bank error signal to yield the bank steering command signal.
(4)
Prior to GS capture, the pitch channel uses either altitude hold or manual pitch commands to generate pitch steering commands. After GS capture, these are switched out and the pitch channel uses glide slope deviation signals and a pitchdown bias which causes an approximate 2 degrees pitchdown command. This bias is cancelled after 15 seconds by the low pass filter which passes changing signals but shunts steady-state signals. The glide slope deviation signal is applied from the navigation receiver to the computer and is proportional to the angular displacement of the airplane from the selected glide slope path. This signal is converted to ac and amplified. This amplification is controlled by the glide slope gain programming during approach and is described under Time Base Glide Slope Gain Programs. Glide slope deviation is amplified, fed to the glide slope capture sensor and is mixed with the pitch attitude signal to produce the pitch steering command signal.
(5)
The AUTO APP mode can also be initiated from the HDG mode. This is accomplished by first turning the flight director mode selector to the HDG position and then to the AUTO APP mode. The computer will operate in the HDG V/L submode until LOC capture. LOC capture will automatically arm the computer for capture of the glide slope beam. The computer will then operate in the AUTO APP mode as described above.
579
34-26-0 Page 16 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. Feb 15/79
H. GS MAN Mode
(1) In this mode of operation, automatic sensing of the glide slope beam, through the GS beam sensor is eliminated. A voltage from the mode selector switch, replaces the GS capture signal, and loss of GS AUTO mode voltage deactivates the sensor. Also, the annunciator will show G/S engaged (green).
I. Time Base Glide Slope Gain Programs (Fig. 3 and 4)
(1)
The purpose of glide slope gain programming is to reduce the pitch steering channel gain (by resistance-capacity time-constant circuitry). This enables the pilot to keep the airplane in the glide slope beam as he maneuvers the airplane to align the V-bars against the miniature airplane in the ADI despite beam irregularities and reduced beam width close in to the airfield. This pitch channel gain is the ratio of pitch command to glide slope deviation. The various gain parameters are preset to specified values. Pitch channel gain is automatically reduced by signal trips from the radio altimeter and marker beacon receiver systems.
(2)
Prior to commencement of gain program No. 1, with the mode selector set to AUTO APP, the pitch channel operates at a gain 1 level. Upon glide slope beam capture, and either upon receipt of a 1500-foot radio altimeter signal trip and RA VALID signal or upon an RA INVALID signal, the pitch channel gain is reduced from gain 1 over a 120-second period to nominal gain. This gain is then maintained until either a middle marker or 200-foot radio altimeter trip executes commencement of gain program No. 2 which is initiated by the GS-2 signal. The pitch channel gain is then further reduced from nominal gain to gain 2 over a 7.5-second period, and this gain figure is now maintained until either the airplane has landed, or go-around mode is selected.
(3)
If GS MAN mode is selected prior to the end of gain program No. 1, the GS manual signal is generated and the pitch channel gain is reduced immediately to nominal gain, eliminating the rest of gain program No. 1. However, gain program No. 2 will still follow as described above.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737 AMM 飞机维护手册 通讯描述和操作(119)
