(5)
Install a new seal (6).
(6)
Connect the coaxial connector (1) to the antenna (3).
(7)
Put the antenna (3) in position on the fuselage (2).
(8)
Attach the antenna (3) with the screws (4).
(9)
Remove the sealant which is not necessary.
(10)
Apply a sealing bead with SEALANTS (Material No. 09-016) around the antenna (3).
(11)
Apply SEALANTS (Material No. 09-016) on the screw (4) heads.
(12)
Make the contour of the screws (4) and the antenna (3) smooth.
1EFF : ALL 1 34-55-18Page 407 1 1 May 01/05 1 1 1CES 1 Subtask 34-55-18-865-052
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 2RS1
Subtask 34-55-18-720-050
C. Do the functional test of the VOR/MKR (para. MKR Identification and Reception test) (Ref. TASK 34-55-00-720-001).
5. Close-up
________ Subtask 34-55-18-860-050
A. Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 34-55-18Page 408 1 1 Feb 01/00 1 1 1CES 1
RECEIVER - VOR/MARKER (3RS1,3RS2) - REMOVAL/INSTALLATION
________________________________________________________ TASK 34-55-31-000-001 Removal of the VOR/MKR Receiver (3RS1, 3RS2)
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific access platform 1.6 m (5 ft. 3 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
34-55-31-991-001 Fig. 401
3. Job Set-up
__________ Subtask 34-55-31-865-050
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 3RS1
49VU NAV/VOR/1 2RS1 G13 FOR 3RS2 121VU COM NAV/VOR/2 2RS2 K08
1EFF : ALL 1 34-55-31Page 401 1 1 Feb 01/98 1 1 1CES 1 Subtask 34-55-31-010-050
B. Get Access
(1)
Put the access platform in position at the access door 824 in zone
128.
(2)
Open the access door 824.
4. Procedure
_________
(Ref. Fig. 401/TASK 34-55-31-991-001) Subtask 34-55-31-020-050
A. Removal of the VOR/MKR Receiver
(1)
Loosen the nuts (4).
(2)
Lower the nuts (4).
(3)
Pull the VOR/MKR receiver (1) on its rack (3) to disconnect the electrical connectors (2).
(4)
Remove the VOR/MKR receiver (1) from its rack (3).
(5)
Put blanking caps on the disconnected electrical connectors (2).
1EFF : ALL 1 34-55-31Page 402 1 1 Feb 01/98 1 1 1CES 1
VOR/MKR Receiver
Figure 401/TASK 34-55-31-991-001
1EFF : ALL 1 34-55-31 Page 403
1 1 Feb 01/98
1 1
1CES 1
TASK 34-55-31-400-001
Installation of the VOR/MKR Receiver (3RS1, 3RS2)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 1.6 m (5 ft. 3 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
34-55-00-740-002 BITE Test of the VOR/MKR R 52-41-00-410-002 Close the Avionics Compartment Doors after Access 34-55-31-991-001 Fig. 401
3. Job Set-up
__________
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM NAVIGATION 导航4(180)
