3. Job Set-up
__________ R **ON A/C 001-049, 051-099, 101-105, 151-199,
Subtask 34-53-00-860-053
A. Aircraft Maintenance Configuration
(1)
Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
(2)
Do the ADIRS start procedure (Ref. TASK 34-10-00-860-002).
1EFF : ALL 1 34-53-00Page 501 1 1 May 01/05 1 1 1CES 1
(3)
Do the IR alignment procedure
(Ref. TASK 34-10-00-860-004).
(4)
On the EFIS control sections of the FCU:
-
set the ADF/VOR selector switches to ADF
-
set the mode selector switches to ROSE/NAV.
(5)
On the center pedestal, on the MCDU:
-get the SYSTEM REPORT/TEST/NAV page
(Ref. TASK 31-32-00-860-010)
-push the NEXT PAGE function key.
(6)
On the center pedestal, on the RMP1 (RMP2):
-set the ON/OFF switch to ON
-push the NAV pushbutton switch (the green LED on this pushbutton switch comes on)
-tune ADF1 and ADF2 to a non local station (frequency more than 750 KHz). (Ref. Fig. 501/TASK 34-53-00-991-002)
R **ON A/C 106-149, 201-299, 301-399, 401-499,
Subtask 34-53-00-860-053-A
A. Aircraft Maintenance Configuration
(1)
Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
(2)
Do the ADIRS start procedure (Ref. TASK 34-10-00-860-002).
(3)
Do the IR alignment procedure
(Ref. TASK 34-10-00-860-004).
(4)
On the EFIS control sections of the FCU:
-
set the ADF/VOR selector switches to ADF.
-
set the mode selector switches to ROSE/NAV.
(5)
On the center pedestal, on the MCDU:
-get the SYSTEM REPORT/TEST/NAV page
(Ref. TASK 31-32-00-860-010)
-push the NEXT PAGE function key.
1EFF : ALL 1 34-53-00Page 502 1 1 Aug 01/05 1 1 1CES 1
ADF-Frequency Selection
Figure 501/TASK 34-53-00-991-002
1EFF : ALL 1 34-53-00 Page 503
1 1 Feb 01/98
1 1
1CES 1
(6)
On the center pedestal, on the RMP1 (RMP2):
-set the ON/OFF switch to ON
-push the NAV pushbutton switch (the green LED on this pushbutton switch comes on)
-tune ADF1 and ADF2 to a non local station (frequency more than 750 KHz). (Ref. Fig. 501/TASK 34-53-00-991-002)
(7)
On the VOR/ADF/DME RMI:
-set the VOR/ADF selector switches to ADF.
**ON A/C ALL
Subtask 34-53-00-865-055
B. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU NAV/VOR/DME/RMI 12FN F13 49VU NAV/ADF/1 1RP1 H14 121VU COM NAV/ADF/2 1RP2 K02
4. Procedure
_________
R **ON A/C 001-049, 051-051, 053-099, 101-105, 151-199,
Subtask 34-53-00-740-050
A. BITE Test of the ADF
NOTE : During the BITE TEST (ADF1 or 2) by the MCDU, the indications
____ related to the two receivers (Capt and F/O) are shown at the same time.This has no effect on the test or component.
1EFF : ALL 1 34-53-00Page 504 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU: On the MCDU:
- push the line key adjacent to the ADF1 (ADF2) indication. - the ADF1 (ADF2) page comes into view.
- push the line key adjacent to the TEST indication. - the INITIAL CONDITIONS are shown(page 1 to 3).
- push the line key adjacent to the START TEST indication. - the TEST IN PROGRESS 13S indicationcomes into view.
From 0 to 6s: - On the CAPT and F/O NDs: * the ADF1 (ADF2) pointer dissapears. * the RED ADF1 (ADF2) warning message comes into view.
From 6 to 13s: - On the CAPT and F/O NDs: * the ADF1 (ADF2) pointer comes into view, moves to a relative bearing of 135..
On the MCDU: On the MCDU:
- push the line key adjacent to the YES indication. the TEST OK indication comes into view.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM NAVIGATION 导航4(152)
