737-300 400 500 AMM 飞机维护手册 STANDARD PRACTICES(91)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 NOTE:____ While the ADL does a self test, the display indicators can flash on and off. TEST IN PROG, TEST COMPLETE and then UNIT READY will show on the display.
 (8)  S 862-037Make sure that the circuit breakers are closed for the applicable component or system that will receive the new software.
 (9)  S 422-038Do these steps at the ADL to install the software:
 NOTE:____ You must know the correct software part numbers for the component. For the component to be an approved installation, software with the correct part numbers must be installed.
 NOTE:____ This is a general procedure for software installation. Some components have other steps that are necessary. The software installation task for the component will include all necessary steps.
 (a)  Set the system select switch on the data loader control panel to the applicable position for your component or system.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-15-11
 ALL  ú ú 02 Page 215 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b) Carefully push the first disk (label up) into the disk drive.
 NOTE: If the destination component is active, the
____ installation sequence will begin. READY and then TRANSF IN PROG will show on the display. Then the display will show the data bus transmitter number and the amount of data. If there is more than one file, the ADL will install the next file until all files are completed. If the software is on more than one disk, the display will show DISK CHANGE or INSERT DISK when it is time to put in the subsequent disk.
 NOTE: If TRANSF FAIL shows, then the installation is not
____ completed. Open and close the circuit breaker for the component, and start the installation again.
 IF DISK ERROR shows, then there is a problem with the disk. Open and close the circuit breaker for the component, and start the installation again. If the problem continues, then replace the disk.
 (c)  If DISK CHANGE or INSERT DISK shows in the display, wait approximately 10 seconds and then push the eject button.
 NOTE: The installation can fail if you wait too long
____ before you remove and install disks.
 1) Remove the disk from the disk drive. 2) Put the subsequent disk into the disk drive. 3) If there are more than two disks for the software
 installation, then remove and install disks until the display shows TRANSF COMPLETE.
 (d)  
When TRANSF COMPLETE shows on the display, wait approximately 10 seconds and then push the eject button.

 (e)  
Remove the disk from the disk drive.

 (f)  
If there was a plastic protective disk in the disk drive before you installed software, then put it back into the disk drive.

 S 862-039
 (10)
 Set the system select switch on the data loader control panel to the NORM position.

 (11)
 Close the front cover on the ADL.

 S 412-040
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-15-11
 ALL  ú ú 02 Page 216 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 742-041
 (12) Make sure that the correct software part numbers are installed in the component.
 NOTE: The software installation task for the component has the
____
 steps to do a software configuration check.

 S 862-042
 (13) Remove electrical power (AMM 24-22-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-15-11
 ALL  ú ú 01 Page 217 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 SELF-LUBRICATED BEARINGS AND BUSHINGS - INSPECTION/CHECK
________________________________________________________
 1.  General_______
 A.  This procedure contains three tasks:
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 STANDARD PRACTICES(91)