20-10-10
ALL ú ú 02 Page 403 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
Turnbuckle Lockwire Installation
Figure 402
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-10
ALL ú ú 01 Page 404 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
H85180
A
737-300/400/500MAINTENANCE MANUAL
(g) Push twisted ends back to lie flat against terminal.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-10
ALL ú ú 01 Page 405 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
PRESSURE-SENSITIVE DECALS - REMOVAL/INSTALLATION
________________________________________________
1. General_______
A. This procedure contains two tasks:
(1)
Removal of the pressure-sensitive decals.
(2)
Installation of the pressure-sensitive decals.
B. Apply external decal sections in a sequence where the ends make an overlap downstream from the line of flight.
C. All exterior decals require edge sealing using paint or an edge sealer unless specified differently.
D. Clean plastic film decals with naphtha. Do not use adhesive activator.
E. You can remove air bubbles in the eight hours after you apply the decal. Make a small hole in the decal film with a sharp pointed instrument, at the edge of bubble, and push air out through the hole.
F. You can also install interior decals with the same procedure you use for pressure-sensitive placards (AMM 20-10-14/401).
TASK 20-10-11-204-018
2. Remove Pressure-Sensitive Decals________________________________
A. Equipment
(1)
Plastic Scraper or Spatula
(2)
Source of heat - 120°F, for example, hot air blast or light bulb
B. Consumable Materials
(1)
B00068 Solvent, Ethyl alcohol, denatured
(2)
B00130 Solvent, Isopropyl Alcohol
(3)
G00033 Cheesecloth - BMS 15-5
C. References
(1) AMM 51-21-11/701, Interior and Exterior Finishes (Paint Stripping)
D. Procedure
S 024-002
(1) To remove external decals, paint strip (AMM 51-21-11/701).
S 024-023
CAUTION: THE TEMPERATURE OF THE SURFACE TO WHICH THE DECAL IS APPLIED
_______
MUST NOT BE MORE THAN 130°F.
(2) To remove internal decals, use heat or use solvent.
(a) To remove decals with heat, do these steps:
1) Heat the decal to approximately 120°F until the adhesive becomes soft.
NOTE:____If you use too much heat, the decal will melt. If the decal melts, remove it with solvent.
2) Lift the corner of the decal with a sharp spatula or knife blade and remove the decal from the surface.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-11
ALL ú ú 02 Page 401 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
3) If necessary, clean the surface. Use a cheesecloth pad that is moist with a solution of one-half cleaner and one-half water.
(b) To remove decals with solvent, do these steps: 1) Apply CDG-110, CDG-211, isopropyl alcohol, or ethyl alcohol to the decal with a brush or cloth. 2) When the decal has wrinkles (after approximately two minutes), apply solvent again. 3) After approximately two minutes, move the soft decal off of the surface or remove with a spatula.
4) If necessary, clean the surface with a cheesecloth pad that is moist with CDG-110, CDG-211, isopropyl alcohol, or ethyl alcohol.
TASK 20-10-11-204-019
3. Install Pressure-Sensitive Decals_________________________________
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 STANDARD PRACTICES(12)
