DEUTSCH STANDARD TOOLS
TABLE A
TUBE SIZE SWAGE TOOL ASSEMBLY ASSEMBLY SWAGE HEAD POWER UNIT GAGE INSPECTION
04 DLT05PSKT3000 DLT05PSHA3004 DLT05MAPW0000 D12-9892-04
06 DLT10PSKT3000 DLT05PSHA3006 DLT10MAPW0000 D12-9892-06
08 10 DLT20PSKT3000 DLT05PSHA3010 DLT05PSHA3008 DLT20MAPW0000 D12-9892-08
D12-9892-10
12 DLT30PSKT3000 DLT30PSHA3012 DLT30MAPW0000 D12-9892-12
16 DLT40PSKT3002 DLT40PSHA4016 DLT40MAPW0000 D12-9892-16
20 DLT40PSKT3003 DLT40PSHA3020 DLT40MAPW0000 D12-9892-20
NOTE: One of the following pumps is necessary to actuate the power units: . DTL02MAPP1000 pneumatic pump 10,000 psi . DLT01MAPM1000 manual pump 10,000 psi
DEUTSCH LIGHTWEIGHT TOOLS TABLE B
* NOTE: The -12 size swage die is different in outer diameter than the swage dies used before.
Swage and Inspection Tool Part Numbers
Figure 825
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-51
ALL ú ú 02 Page 880F ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L10680
A 737-300/400/500MAINTENANCE MANUAL
NOTE: ALL DIMENSIONS ARE IN INCHES.
Minimum Straight Length for Permaswage Fitting Installation
Figure 826
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-51
ALL ú ú 02 Page 880G ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L10687
A 737-300/400/500MAINTENANCE MANUAL
TUBE
THE A DIMENSION IS SHOWN IN FIG. 829.
Tube Splice Repair
Figure 827
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-51
ALL ú ú 02 Page 880H ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L10836
A 737-300/400/500MAINTENANCE MANUAL
MATERIAL SURFACE Bare or alodine PROCEDURE TO CLEAN TUBE Solvent clean
Anodize Hand apply abrasive material, 180-grit or finer: Abrasive Scotch Brite, Type A . Fed Spec P-P-121 . Fed Spec P-C-451 .
Primer/paint 2.1. lacquer base paint/enamel Hand apply abrasive material, 240-grit or finer Lacquer thinner (refer to TT-T-266) (flammable) for primed surfaces (MIL-P-6889) and (flammable) MEK (refer to TT-T-261)
Cleaning and Paint Removal Procedures for Aluminum Tubes
Figure 828
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-51
ALL ú ú 02 Page 880I ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L10840
A 737-300/400/500MAINTENANCE MANUAL
0.150 INCH MIN
A
MARK FOR THE MINIMUM TUBE INSERTION DEPTHS
Witness Mark Location and Usual Marking Procedures
Figure 829
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-51
ALL ú ú 02 Page 880J ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L10889
A 737-300/400/500MAINTENANCE MANUAL
INSERTION WITNESS MARK BE
CLEAR OF THE FITTING END
TUBE DIAMETER (INCHES) 1/4 (04) MAX A DIMENSIONS SWAGED DIAMETER (INCHES) 0.315 B DIMENSIONS SWAGED LENGTH MIN (INCHES) 0.46 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：737-300 400 500 AMM 飞机维护手册 STANDARD PRACTICES(69)
