20-10-53
ALL ú ú 02 Page 402 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(3) G02503 Lace - Black Nylon Untreated Sleaving (1/8")
B. Procedure - Install the Protective Lacing (Fig. 401)
S 404-012
(1)
Install the lacing per Figure 401, steps 1 through 3, except nose landing gear.
S 404-013
(2)
Install the lacing on nose landing gear per Figure 401 , steps 1 through 3.
(a)
Prior to pulling lock lace through, before Step 3, apply adhesive to the laces.
(b)
Pull the laces into place, (Step 3), this will bond the laces in place.
(c)
Apply two layers of tape over the lacing. 1) Spirally wrap each layer with a 50% overlap and reverse the direction of the spiral with each layer.
2) Extend the tape 1.0 inch to 1.5 inch beyond each end of the lacing.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-53
ALL ú ú 01 Page 403 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
HOSE OR CONDUIT
SLEEVING WOVEN NYLON
STEP 1
TEN WRAPS APPROXIMATELY STEP 2
0.75 1.50
CUT OFF 0.25 MAX STEP 3 (LACING) OF THE SERVING FROM EITHER END TIE CAN BE MADE CUT OFF 0.25 MAX
Figure 401 Protective Lacing Installation FOR TWO OR MORE HOSES NOTE: ALL DIMENSIONS ARE IN INCHES.____
K04566
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-53
ALL ú ú 01 Page 404 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
STENCIL MARKINGS - REMOVAL/INSTALLATION
_______________________________________
1. General
_______
A. This procedure contains one task. The task is the installation of stencil or insignia markings.
B. For decorative finishes used on external surfaces of the airplane, refer to "Decorative Exterior Finishes" (AMM 51-21-99/701).
C. The surface you paint and the type of finish necessary will tell you which paint to use for markings. Make sure the paint is applicable with the initial surface finish.
D. In areas where a skydrol 500 resistant finish is necessary, apply BMS 10-60 Type II enamel.
E. Where the letters are less than two inches in height and width, use BMS 10-60 enamel for the letters.
NOTE: Use BMS 10-79, Type II primer on painted or unpainted surfaces
____
when you use BMS 10-60, Type II.
F. For markings installed directly on corogard EC 843 or EC 843S,
use EC 942 black.
TASK 20-10-61-374-001
2. Stencil or Insignia Markings - Installation
___________________________________________
A. General
(1)
Make sure you do not get clean surfaces dirty when you clean adjacent surfaces.
(2)
Use a polyethylene wash bottle to apply solvents. Make sure you know the contents of the bottle.
(3)
Avoid overspray contamination of adjacent areas.
(4)
Make sure all coatings or finishes are uniform, homogeneous, and free from gelled particles.
(5)
Apply primer and stencil paint with spray equipment only. Do not spray adjacent surfaces.
(6)
Make sure all coating or finish materials are mixed correctly and identified with a label. Discard materials with expired pot life.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-10-61
ALL ú ú 01 Page 401 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
B.
C.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 STANDARD PRACTICES(75)
