NOTE: Apply sealant (RTV 157) 1.2 mm thick from the edges to prevent metal to metal contact. 3
Install the tray table inlay (150).
4
Install the igus carriages (80), (90) to the igus rails (120).
NOTE: Verify smoothness of motion for carriages prior to locking screws.
Recaro Aircraft Seating GmbH & Co. KG, Daimlerstrasse 21, D.74523 Schw.bisch Hall
COMPONENT MAINTENANCE MANUAL . 6510A TYPE 654 SERIES
5 Install the screws (40), the upper lever arm stop (50) and the dowel pin (60) to the table
arm (30).
6 Install the screws (70) and the table arm (30).
NOTE: Verify smoothness of motion for carriages prior to locking screws.
7 Install the set screws (170), the tray table shaft (20) and the arm table assy (10).
NOTE: Maximum pull force for the arm table assy (10) is 30,0 +/. 5,0 Newton or 6.7 +/.
1.1 lbs after assembled.
(5) ASSEMBLY OF THE CENTER CONSOLE (Refer to IPL figure 4) NOTE: Safety all screws with threadlocking compound (Loctite 243). EFFECT: BA730020100
(a) Assembly of the Center Console 1 Install the cable guide (580). 2 Install the privacy divider assy (530) with the nuts (560), the washers (550) and the
screws (540), (570) to the panel assy (600). 3 Install the drip shield (520) with the screw (170). 4 Install the cartridge table assy (480), (500) and the rhino body assy (430), (440) with the
screws (490), (510). 5 Install the audio jack support assy (450), (470) with the screws (460). 6 Install the cocktail tray assy (420) with the screws (230). 7 Install the UPCU cradle assy (360), (370) with the nuts (410), the washers (390), (400)
and the mushroom screws (380). 8 Install the elbow cavity assy (330), (350) with the screws (340). 9 Install the hinge cover assy (270), (280) and the arm rest assy (290), (310) with the
screws (300), (320). 10 Install the hand rail (220). 11 Install the top front cover assy (240) and the manual release cover assy (250), (260) with
the screws (170). 12 Install the cosmetic backing plate (200) and the bumper strip (190) with the screws (210).
Recaro Aircraft Seating GmbH & Co. KG, Daimlerstrasse 21, D.74523 Schw.bisch Hall
COMPONENT MAINTENANCE MANUAL . 6510A TYPE 654 SERIES
13 Install the rear cover assy (160) with the screws (170).
14 Install the stowage bin assy (180) with the screws (170).
15 Install the command center (120) with the screws (130), (140) and the washers (150).
16 Add two (2) strips per side of double sided foam tape (BA980012) to the life vest liner
(100), (110). 17 Install the life vest liner (100), (110). 18 Install the front cover assy (60) with the screws (70). 19 Install the lower life vest bracket (80) and the life vest door assy (50) with the screws (90). 20 Close the life vest door assy (50). 21 Install the side cover assy (30), (40). 22 Install the access cover assy (10), (20). 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：COMPONENT MAINTENANCE MANUAL WITH ILLUSTRATED PARTS LIST B757−200 PASSENGER SEAT 乘客座椅(40)
