(a) Replace the applicable uplock assembly:
- for the MLG uplock proximity sensor faults (8GA; 9GA; 10GA; 11GA) replace the applicable uplock assembly 2509GM (2510GM), (Ref. AMM TASK 32-31-44-000-001) and (Ref. AMM TASK 32-31-44-400-001).
- for the NLG uplock proximity sensor faults (12GA; 13GA) replace the uplock assembly 2530GM, (Ref. AMM TASK 32-31-21-000-001) and (Ref. AMM TASK 32-31-21-400-001).
- for the MLG door uplock proximity sensor faults (26GA; 27GA; 28GA; 29GA) replace the MLG door uplock assembly 2521GM (2520GM), (Ref. AMM TASK 32-31-33-000-001) and (Ref. AMM TASK 32-31-33-400-002).
- for the NLG door uplock proximity sensor faults (30GA; 31GA) replace the door uplock assembly 2534GM, (Ref. AMM TASK 32-31-14-000-001) and (Ref. AMM TASK 32-31-14-400-001).
(b) if the fault continues, do step (7).
(6) If the proximity sensor is serviceable, do the applicable functional or operational test that follows, to confirm that the fault occurs:
- for the MLG (Ref. AMM TASK 32-31-00-720-002)
- for the NLG only (Ref. AMM TASK 32-31-00-720-003)
- for the L/G doors (Ref. AMM TASK 32-31-00-710-002) or (Ref. AMM TASK 32-31-00-710-002).
- if the fault continues, do the next step.
(7) Replace the applicable LGCIU-1 (5GA1) or LGCIU-2 (5GA2) which identified the fault, (Ref. AMM TASK 32-31-71-000-001) and (Ref. AMM TASK 32-31-71-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞32-31-00∞∞∞∞∞∞∞∞∞∞Page A221
Aug 01/05R
CES TASK 32-31-00-810-855
MLG Vibration and Noise During Retraction and Exetension, and/or MLG FWD Pintle Bearing Lubrication Difficult.
1. Possible Causes
_______________
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 12-22-32-640-001 Lubrication of the MLG and Doors
3. Fault Confirmation
__________________
A. Test
(1) If the conditions that follow are shown, do the fault isolation.
(a) During retraction and extension of the landing gear there is vibration and noise.
(b) During servicing, the MLG FWD pintle bearing is difficult to lubricate.
4. Fault Isolation
_______________
A. Procedure
(1) Lubricate the FWD pintle bearing (Ref. AMM TASK 12-22-32-640-001), use both grease nipples (when accessible). Lubricate for another 20 strokes after fresh grease comes out of the pintle bearing.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞32-31-00∞∞∞∞∞∞∞∞∞∞Page A222
Aug 01/05R
CES TASK 32-31-00-810-856
NLG Doors Do Not Open Fully
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
1. Possible Causes
_______________
- ACTG CYL-NLG DOOR (2531GM)
- SAFETY VALVE-NLG DOOR OPENING (2630GM)
- nose landing gear doors operating mechanism
- nose gear door gaps and mismatches
- NLG proximity sensor and target clearances
- NLG door uplock units and pins
- rotating rod of the nose gear aft door
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 32-22-00-200-001 Visual Inspection of the Rotating Rod of the
Nose-Gear Aft Door AMM 32-22-00-220-001 Check of the Nose-Gear Doors Gaps and Mismatches AMM 32-30-00-200-001 Detailed Inspection of Nose Gear Door Operating
Mechanism AMM 32-31-00-200-001 Detailed Inspection of Gear Uplock and Door Uplock Units and Pins AMM 32-31-00-720-003 Functional Test of the Normal Extension and
Retraction of the Nose Landing Gear AMM 32-31-16-000-001 Removal of the NLG Door Actuating Cylinder (2531GM) AMM 32-31-16-400-001 Installation of the NLG Door Actuating Cylinder
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 起落架 LANDING GEAR 1(48)
