(8) If there is a circuit/interface fault do the repair.
(9) Do the L/G BITE test as in Para.3.A.(1)
(10) If no fault is found at Para.4.A.(7), replace the LGCIU-1 (5GA1) or LGCIU-2 (5GA2) (Ref. AMM TASK 32-31-71-000-001) (Ref. AMM TASK 32-31-71-400-001).
(11) Do the GROUND SCANNING and make sure that the ground log is clear.
5. Close-up
________
A. Put the aircraft back to its initial configuration.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞32-31-00∞∞∞∞∞∞∞∞∞∞Page 234
May 01/05R
CES
TASK 32-31-00-810-817
LLG Door Open Proximity Sensor Fault (33GA, 35GA)
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
1. Possible Causes
_______________
- LGCIU-1 (5GA1)
- LGCIU-2 (5GA2)
- 33GA
- 35GA
- aircraft wiring
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific Multimeter
No specific 50Vdc Isolation Tester
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
ASM 323103S01
ASM 323103S01004
ASM 323104S01
AMM 32-12-00-010-001 Open the Main Gear Doors for Access
AMM 32-31-71-000-001 Removal of the LGCIU (5GA1, 5GA2)
AMM 32-31-71-400-001 Installation of the LGCIU (5GA1, 5GA2)
AMM 32-31-73-000-001 Removal of the Proximity-Sensors 9GA(8GA),
11GA(10GA), 27GA(26GA), 29GA(28GA), 15GA(14GA), 17GA(16GA), 21GA(20GA), 23GA(22GA), 33GA(32GA), 35GA(34GA)
AMM 32-31-73-400-001 Installation of the Proximity-Sensors 9GA(8GA), 11GA(10GA), 27GA(26GA), 29GA(28GA), 15GA(14GA), 17GA(16GA), 21GA(20GA), 23GA(22GA), 33GA(32GA)...
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞32-31-00∞∞∞∞∞∞∞∞∞∞Page 235
May 01/05R CES
-------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 32-69-00-740-001 BITE Check Landing Gear Control Interface Unit (LGCIU) using MCDU to Ensure that Continuous BITE is Operative
3. Fault Confirmation
__________________
A. Message Analysis.
(1) Do a BITE test on the LGCIU-1 (2) (Ref. AMM TASK 32-69-00-740-001)
(a) Access LGCIU-1 (2) TROUBLE SHOOTING (ground) and read the BITE test fault number(s) for fault confirmation (refer to AMM 326900 table 4).
NOTE : The table 4 shows the fault messages approximate to the
____
CFDS message
(2) Do the fault isolation.
4. Fault Isolation
_______________
A. Procedure.
(1) Open the L L/G Door for access to the proximity sensor (Ref. AMM TASK 32-12-00-010-001)
(2) Refer to (Ref. AMM TASK 32-31-73-000-001) Figure 405/TASK 32-31-73-991-005, and find the proximity sensor 33GA 35GA.
(3) Release the electrical connector for the BITE shown failed proximity sensor.
NOTE : If the ELDEC proximity sensor test unit is available. Go to
____ page block 301 and do the procedure in table 5.
(4) Use a Multimeter and do a check of the resistance between the pins A and B of the PROX SNSR, (Ref. ASM 323103S01004) (Ref. ASM 323104S01) the resistance must be approximately 13ohms.
(5) On the PROX SNSR do a check of the circuit isolation.
(a) Connect the pins A and B together.
(b) Connect one test lead of the 50Vdc Isolation Tester to the pins AB and the other test lead to the case.
(c) Supply a test signal for 5 seconds and read the resistance value shown.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞32-31-00∞∞∞∞∞∞∞∞∞∞Page 236
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 起落架 LANDING GEAR 1(16)
