R 1EFF : 201-210, 1 46-21-00Page 310 1 1 Feb 01/05 1 1 1CES 1
R **ON A/C 401-499,
R Subtask 46-21-00-280-092-B
R F. On the MCDU, do a Check of the Reference of the AOC Software/Database
R pre-loaded in the ATSU.
R -------------------------------------------------------------------------------
R ACTION RESULT
R -------------------------------------------------------------------------------
R 1. On the MCDU, on the AOC MENU On the MCDU:
R page: - the CONFIGURATION page comes into
R - push line key adjacent to the view.
R CONFIGURATION indication. On this page:
R - make sure that there is no AOC
R Software/Database part number
R reference shown or that the AOC
R Software/Database part number
R reference is not the same as the
R reference read on the disk(s) of the
R AOC Software/Database 22TX/24TX
R before you do the uploading procedure
R in Para. 4.B.
R **ON A/C 106-149, 151-199, 201-299, 301-399, 401-499,
4. Procedure_________
**ON A/C 151-158, 201-209,
Subtask 46-21-00-970-053
A. Uploading of the ATSU A/C INTERFACE Software (20TX)
NOTE : The loading time for a full disk is twelve minutes approximately.____
NOTE : After the uploading procedures, the operator must do a check of____
the reference of the data loaded in the computer, on the MCDU.
R 1EFF : 106-149, 151-199, 201-299, 301-399, 1 46-21-00Page 311 1401-499, 1Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
1. On the overhead panel, on the Data Loading Selector:
-set the ON/OFF switch to ON.
2. On the overhead panel, on the Data Loading Selector:
-push the PREV or NEXT key until you get the ATSU indication.
3. On the MDDU:
-put the disk of the ATSU A/C INTERFACE Software (20TX) into the disk drive, the label in the forward direction.
4. On the overhead panel, on the Data Loading Selector:
-push the SEL CTL key.
On the display of the Data LoadingSelector:
-DB/N: PUSH NEXT/PREV indication is shown.
On the Multipurpose Disk Drive Unit (MDDU):
-the < < MDDU READY > > indication is shown.
On the display of the Data LoadingSelector:
-ATSUNOT SELECTED indication is shown.
On the MDDU:
-the READY indication is shown
-then, the WAIT RESPONSE indication isshown.
On the display of the Data LoadingSelector:
-ATSU SELECTED indication is shown.
On the MDDU:
-the TRANS IN PROG indication is shown.
NOTE : If a transfer fault occurs, we
____ recommend that you wait a minimum of three minutes:
-after you set the ON/OFF switch on the Data Loading Selector to OFF and
-before you start the uploading of the ATSU A/C INTERFACE software again.
1EFF : 151-158, 201-209, 1 46-21-00Page 312 1 1 Aug 01/05R 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
5. On the overhead panel, on the Data Loading Selector:
-push the SEL CTL key.
6. On the MDDU:
-eject the disk from the disk drive.
7. On the overhead panel, on the Data Loading Selector:
-set the ON/OFF switch to OFF.
Thus, the ATSU can complete its Power On Self-Test.
On the upper ECAM DU:
-
the COM ACARS FAULT or DATALINK ATSU FAULT warning is shown.
On the MCDU:
-
the ATSU prompt is not shown.
NOTE : If more than one disk is
____ necessary for uploading, the EJECT DISK and INSERT DISK indications are shown one after the other. They tell the operator to put a new disk into the MDDU.
-when all the disks are loaded into the computer, the TRANSF COMPLETE indication is shown.
On the display of the Data LoadingSelector:
-ATSU NOT SELECTED indication is shown.
On the MDDU:
-
the < < MDDU READY > > indication isshown.
On the upper ECAM DU:
-
the COM ACARS FAULT or DATALINK ATSUFAULT warning goes out of view after approximately one minute.
NOTE : When the ON/OFF switch on the
____ Data Loading Selector is set to OFF, the ATSU does a Power On Self Test (POST). The COM ACARS FAULT or DATALINK ATSU FAULT warning goes out of view at the end of this test.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM 信息系统 INFORMATION SYSTEMS(38)
