(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 28-46-16-420-050
B. Installation of the Overflow Sensor
(1)
Install the sensor (3) with the bolts (1) and (5) and the washers (2) and (6).
(2)
TORQUE the bolt (1) to between 0.45 and 0.56 m.daN (39.82 and 49.55 lbf.in).
(3)
TORQUE the bolt (7) to between 0.225 and 0.28 m.daN (19.91 and 24.77 lbf.in).
1EFF : ALL 1 28-46-16Page 410 1 1 Aug 01/05 1 1 1CES 1 1EFF : ALL 1 28-46-16Page 411 1 1 May 01/04 1 1 1CES 1 Subtask 28-46-16-740-050
(4) Apply SEALANTS (Material No. 09-007) to the bolts (1) and (7).
(5) Remove the blanking caps from the electrical connectors.
(6) Connect the electrical connectors of the cable (5) and tighten the connector screws (8).
(7) Install the cable (5) in the cable clamp and tighten the cable clamp screw (41).
R **ON A/C 301-399,
R Subtask 28-46-16-420-050-A
R B. Installation of the Overflow Sensor
R (1) Install the cover (4) and the sensor (3) on the support bracket.
R (2) Install the bolts (1) and (8) and the washers (2) and (7).
R R (3) TORQUE the bolt (1) to between 0.45 and 0.56 m.daN (39.82 and 49.55 lbf.in).
R R (4) TORQUE the bolt (8) to between 0.225 and 0.28 m.daN (19.91 and 24.77 lbf.in).
R (5) Apply SEALANTS (Material No. 09-007) to the bolts (1) and (8).
R (6) Remove the blanking caps from the electrical connectors.
R R (7) Connect the electrical connectors of the cable (6) and tighten the connector screws (9).
R R (8) Install the cable (6) in the cable clamp and tighten the cable clamp screw (5).
R **ON A/C ALL
Subtask 28-46-16-865-052
R C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1QP, 2QP, 43QJ, 44QJ.
D. BITE Test
(1) Do the tank-level-sensing functional (BITE) test (Ref. TASK 28-46-00-740-001).
5. Close-up
________ Subtask 28-46-16-410-051
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panel (Ref. TASK 28-12-45-400-002):
-
FOR 28QJ1
install 550CB
-
FOR 28QJ2
install 650CB.
Subtask 28-46-16-650-052
B. Fuel Configuration
(1) Refuel, defuel or transfer fuel as necessary (Ref. TASK 12-11-28-650-003), (Ref. TASK 28-25-00-650-001) or (Ref. TASK 28-25-00-869-001).
Subtask 28-46-16-942-051
C. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 28-46-16Page 412 1 1 May 01/04 1 1 1CES 1 SENSOR - TEMPERATURE, WING TANK (29QJ1,29QJ2,30QJ1,30QJ2)
_________________________________________________________ REMOVAL/INSTALLATION
____________________
TASK 28-46-17-000-001
Removal of the Temperature Sensor 29QJ1 (29QJ2)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUEL 燃油6(90)
