(2)
Pull the MLI rod (2) out until the magnet (1) touches the seal (3). Continue to pull until the MLI rod is out of the housing.
1EFF : 301-399, 1 28-43-22Page 417 1 1 Aug 01/04 1 1 1CES 1
R Magnetic-Level-Indicator Rod
R Figure 403/TASK 28-43-22-991-003
1EFF : 301-399, 1 28-43-22 Page 418
1 1 May 01/04
1 1
1CES 1
R TASK 28-43-22-400-003
R Installation of the Magnetic-Level-Indicator Rod 206QM(207QM)
R WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING_______
R NOTICES ARE IN POSITION.
R WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______
R GEAR.
R 1. Reason for the Job__________________
R Self Explanatory
R 2. Job Set-up Information______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------
R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific safety barriers
R No specific access platform 3.0 m (9 ft. 10 in.)
R B. Consumable Materials
R -------------------------------------------------------------------------------
R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R Material No. 11-004 USA MIL-T-81533
R 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
R (Ref. 20-31-00)
R Material No. 19-003 USA AMS 3819
R LINT-FREE COTTON CLOTH (Ref. 20-31-00)
R C. Referenced Information
R -------------------------------------------------------------------------------
R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R 28-00-00-910-001 Fuel Safety Procedures
R 28-43-22-991-003 Fig. 403
1EFF : 301-399, 1 28-43-22Page 419 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 28-43-22Page 420 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 28-43-22Page 421 1 1 May 01/04 1 1 1CES 1
R 3. Job Set-up__________
R Subtask 28-43-22-941-056
R A. Safety Precautions
R WARNING : OBEY THE FUEL SAFETY PROCEDURES._______
R (1) Make sure that the safety barriers are in position.
R (2) You must obey the fuel safety procedures (Ref. TASK 28-00-00-910-001)
R when you do work on the fuel system.
R Subtask 28-43-22-860-052
R B. Aircraft Maintenance Configuration
R (1) Make sure that the access platform is below the applicable
R Magnetic-Level-Indicator (MLI) rod (2).
R 4. Procedure_________
R (Ref. Fig. 403/TASK 28-43-22-991-003)
R Subtask 28-43-22-420-054
R A. Preparation for Installation
R WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______
R MATERIALS ONLY WITH A GOOD SUPPLY OF AIR.
R OBEY THE MANUFACTURERS INSTRUCTIONS.
R PUT ON PROTECTIVE CLOTHING.
R DO NOT GET THEM IN YOUR MOUTH.
R DO NOT SMOKE.
R DO NOT BREATHE THE GAS.
R THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT.
R GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
R (1) Clean the component interface and the adjacent areas with
R MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS
R (Material No. 11-004).
R (2) Do an inspection of the component interface and/or the adjacent area.
R (3) Make sure that the parts retained from the removed component are
R clean and in the correct condition.
R Subtask 28-43-22-420-053
R B. Installation of the Magnetic-Level-Indicator Rod 206QM (207QM)
R (1) Install the Magnetic-Level-Indicator (MLI) rod (2) in the MLI
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUEL 燃油6(57)
