______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific warning notices
No specific access platform 11.0 m (36 ft. 1 in.)
98D27207545000 1 PIN - RIGGING
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
No specific lockwire corrosion-resistant steel 0.8 mm (0.032 in.)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002
24-41-00-862-002
29-00-00-864-001
R 29-10-00-863-003 R R 55-33-13-010-002 R R
27-21-48-991-001
3. Job Set-up
__________Energize the Aircraft Electrical Circuits from the External PowerDe-energize the Aircraft Electrical Circuits Supplied from the External PowerPut the Related Hydraulic System in the Depressurized Configuration before Maintenance Action Pressurize the Blue Hydraulic System with a Ground Power Supply Opening/Removal of the Trailing Edge Access-Panels 325EL, 325ER, 325DL, 325DR, 325CL, 325CR, 325BL and 325BRFig. 401
(Ref. Fig. 401/TASK 27-21-48-991-001)
R Subtask 27-21-48-010-050-A
R A. Get Access
R (1) Put the access platform in position.
R (2) Open the access panel 325DL and remove the access panel 325DR R (Ref. TASK 55-33-13-010-002).
Subtask 27-21-48-865-053
B. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AUTO FLT/FAC1/28VDC 5CC1 B04 49VU AUTO FLT/FAC1/26VAC 14CC1 B03 121VU AUTO FLT/RUDDER/TRIM/IND 15CC M20 121VU AUTO FLT/FAC2/28VDC 5CC2 M19 121VU AUTO FLT/FAC2/26VAC 14CC2 M18
Centering Rod - Rudder Control
Figure 401/TASK 27-21-48-991-001
1EFF : ALL 1 27-21-48 Page 403
1 1 Feb 01/98
1 1
1CES 1
Subtask 27-21-48-860-050
C. Aircraft Maintenance Configuration
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES
_______ ARE CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
(1)
Energize the aircraft electrical circuits. (Ref. TASK 24-41-00-861-002)
(2)
Pressurize the Blue hydraulic system with the electric pump. (Ref. TASK 29-10-00-863-003)
(3)
Put the rudder pedals in the neutral position.
(4)
On the center pedestal, on the panel 110VU, make sure that the RUD TRIM indicator shows 0.
(5)
Depressurize the Blue hydraulic system and put it in the maintenance configuration (Ref. TASK 29-00-00-864-001).
(6)
Make sure that the Green and Yellow hydraulic systems are depressurized and put them in the maintenance configuration (Ref. TASK 29-00-00-864-001).
(7)
On the overhead panel 23VU, release the FLT CTL/FAC 1 pushbutton switch. The OFF legend comes on.
(8)
On the overhead panel 24VU, release the FLT CTL/FAC 2 pushbutton switch. The OFF legend comes on.
(9)
Put the warning notices in the cockpit to tell persons not to operate the flight controls.
(10)
De-energize the aircraft electrical circuits. (Ref. TASK 24-41-00-862-002)
(11)
Put the warning notices in position to tell persons not to operate the hydraulic systems:
-in the cockpit on the hydraulic section 40VU of the overhead panel,
- on the ground service panels of the Green, Yellow and Blue hydraulic systems.
(12) Put the PIN - RIGGING (98D27207545000) (20) in the bellcrank assembly
(2) of the travel limitation unit (3).
Subtask 27-21-48-865-050
D. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AUTO FLT/FAC1/28VDC 5CC1 B04
49VU AUTO FLT/FAC1/26VAC 14CC1 B03 121VU AUTO FLT/RUDDER/TRIM/IND 15CC M20 121VU AUTO FLT/FAC2/28VDC 5CC2 M19 121VU AUTO FLT/FAC2/26VAC 14CC2 M18
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵2(50)
