-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______ FALL CAN INJURE OR KILL YOU.
1. Reason for the Job__________________ Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific soft brush No specific warning notices No specific Torque Wrench : range 0.00 to 1.20 m.daN
(0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 2.00 to 20.00 m.daN
(15.00 to 150.00 lbf.ft) 56724S0000 1 Spanner Set
1EFF : ALL 1 27-24-51Page 460 1 1 Aug 01/05R 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
No specific Molykote DX Material No. 09-008E USA AMS 3277 EARLY QUICK REPAIR FUEL TANK SEALANT (Ref. 20-31-00)
Material No. 09-016 USA MIL-PRF-81733D TYPE II CLASS B
CORROSION INHIBITING FILLET CONSISTENCY
(Ref. 20-31-00)
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-24-51-000-001 Removal of the Rudder Servo Control 1025GM/2025GM/3025GM 27-24-51-400-001 Installation of the Rudder Servo Control 1025GM/2025GM/3025GM R CMM 272101 27-24-51-991-006 Fig. 407
3. Job Set-up
__________
Subtask 27-24-51-860-057
A. Aircraft Maintenance Configuration
(1)
Make sure that the rudder pedals are in the neutral position.
(2)
Make sure that the rudder trim control is set at the zero position.
(3)
Make sure that the warning notices are in position to tell persons not operate the flight controls.
(4)
Make sure that the rudder servo control is removed (Ref. TASK 27-24-51-000-001).
4. Procedure_________
(Ref. Fig. 407/TASK 27-24-51-991-006)
Subtask 27-24-51-210-054
A. Preparation for Installation
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Make sure that the rudder servo control is clamped securely to the workshop bench and that you have access to the piston rod (4).
(2) Clean all the parts retained from the removed component with CLEANING AGENTS (Material No. 11-004) and a soft brush.
(3) Make sure that the parts retained from the removed component are in the correct condition.
(4) Apply Molykote DX to the thread, the shaft and the flange of the eye end (1) and to the contact surfaces of the locking washer (3).
Subtask 27-24-51-420-053
R B. Installation of the Rudder Servo-Control Eye-End
R R R R R R R R R WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
R R (1) Assemble the levers (2) and (13) and the locking washer (3) on the eye-end (1).
R (2) Apply the SEALANTS (Material No. 09-008E) to the last two threads in
R the end of the piston rod (4).
R (3) Install the eye-end (1) with the levers (2) and (13) and the locking
R washer (3) in the piston rod (4).
R (4) Attach the spanner to the eye-end (1).
(5) Attach the clamping jaws to the piston rod (4). Make sure that the
tabs of the locking washer (3) engage with the clamping jaws.
R NOTE : The spanner and the clamping jaws are part of the Spanner Set____
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵2(149)
