(11)
Remove the rudder (2) from the vertical stabilizer (1).
(a)
Move the rudder (2) aft and down in the 90 degree direction from the rudder axis until it touches the rubber mat.
(b)
Move the rudder (2) to the left of the aircraft center line.
(c)
Move the rudder (2) aft, away from the vertical stabilizer (1) and lower it onto a rudder support.
(12)
Disconnect the SLING - R/I VERTICAL STABILIZER AND RUDDER (98D55307518000) from the rudder (2).
(13)
Remove the bushes from the hinge locations.
(a)
Remove the bushes (25),(26) from the bracket (11) of the rudder
(2)
at the location of the hinge No. 1.
(Ref. Fig. 403/TASK 27-21-41-991-003)
(b)
Remove the bushes (94),(95) from the brackets (91) of the rudder
(2)
at the locations of the hinges 2,3,4 and 5. (Ref. Fig. 406/TASK 27-21-41-991-006)
(c)
Remove the bushes (54),(55) from the brackets (51) of the rudder
(2)
at the location of the hinge No. 7.
(Ref. Fig. 405/TASK 27-21-41-991-005)
(d)
Remove the bushes (73),(74) from the hinge arm (63) at the location of the hinge No. 6 at rib 9 of the vertical stabilizer (1). (Ref. Fig. 405/TASK 27-21-41-991-005)
(14)
Remove the bushes (47),(48) from the attachment brackets (36) on the rudder (2). (Ref. Fig. 404A/TASK 27-21-41-991-004-A)
R 1EFF : 004-049, 055-099, 101-149, 151-199, 1 27-21-41Page 422 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
**ON A/C ALL
TASK 27-21-41-400-001
Installation of the Rudder
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______
CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific crane
No specific rubber mat
No specific tie wraps
No specific warning notices
No specific access platform 11.0 m (36 ft. 1 in.)
R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00 to 75.00 lbf.ft) No specific Torque Wrench : range 2.00 to 20.00 m.daN
(15.00 to 150.00 lbf.ft) SL90-313-3750 1 TOOL - INSTALLATION, TAB WASHERS STA-LOK NSA5454 SL90-313-5625 1 TOOL - INSTALLATION, TAB WASHERS STA-LOK NSA5454 SL90-313-7500 1 TOOL - INSTALLATION, TAB WASHERS STA-LOK NSA5454 SL90-315-3750 1 WRENCHES - NOTCHED, TIGHTENING OF NUTS NSA5454
R 1EFF : ALL 1 27-21-41Page 423 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
SL90-315-7500 1 WRENCHES - NOTCHED, TIGHTENING OF NUTS NSA5454 SL90-322-5625 1 WRENCHES - NOTCHED, TIGHTENING OF NUTS NSA5454 SL90-349-7500 1 TOOL - INSTALLATION, TAB WASHERS STA-LOK NSA5454 98D27207545000 1 PIN - RIGGING 98D27207547000 1 PIN - RIGGING 98D27207548000 1 PIN - RIGGING 98D55307518000 1 SLING - R/I VERTICAL STABILIZER AND RUDDER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-018
GENERAL PURPOSE ASSEMBLY PASTE (Ref. 20-31-00) Material No. 05-002 USA MIL-P-8116
PUTTY, ZINC CHROMATE GENERAL PURPOSE (Ref. 20-31-00) Material No. 05-005 USA MIL-C-16173 GRADE II
CORROSION PREVENTIVE (Ref. 20-31-00) Material No. 05-052
SELF-ADHES.PVC DISKS FOR HOISTING POINT BLANKING
(Ref. 20-31-00) Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵2(5)
