(b)
Use the TOOL - INSTALLATION, TAB WASHERS STA-LOK NSA5454 (SL90-313-5625) and install the tab washer (28) and the spring ring
(29)
at the slotted nut (27).
(14)
TORQUE and safety the slotted nuts (96) at the hinges Nos. 2, 3, 4 and 5 as follows: (Ref. Fig. 406/TASK 27-21-41-991-006)
(a)
Use the WRENCHES - NOTCHED, TIGHTENING OF NUTS NSA5454 (SL90-322-5625) and TORQUE the slotted nuts (96) to 3.0 m.daN (22.12 lbf.ft).
(b)
Use the TOOL - INSTALLATION, TAB WASHERS STA-LOK NSA5454 (SL90-313-5625) and install the tab washers (97) and the spring rings
(98)
at the slotted nuts (96).
(15)
TORQUE and safety the slotted nut (75) at the hinge No. 6 as follows: (Ref. Fig. 405/TASK 27-21-41-991-005)
(a) TORQUE the slotted nut (75) to 12.0 m.daN (88.49 lbf.ft).
R 1EFF : 004-049, 055-099, 101-149, 151-199, 1 27-21-41Page 441 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(b)
Use the TOOL - INSTALLATION, TAB WASHERS STA-LOK NSA5454 (SL90-349-7500) and install the tab washer (76) and the spring ring
(77)
at the slotted nut (75).
(16)
Tighten and safety the slotted nut (68) at the hinge No. 6 as follows: (Ref. Fig. 405/TASK 27-21-41-991-005)
(a)
Use the WRENCHES - NOTCHED, TIGHTENING OF NUTS NSA5454 (SL90-315-3750) and tighten the slotted nut (68) until it touches the washer (115) on the bolt (66).
(b)
Use the TOOL - INSTALLATION, TAB WASHERS STA-LOK NSA5454 (SL90-313-3750) and install the tab washer (67) and the spring ring (111).
(c)
Install a new cotter pin (65) through the bolt (66) and safety it.
(17)
Connect the servo actuators 1025GM/2025GM/3025GM (35) to the brackets
(36)
of the rudder (2) as follows: (Ref. Fig. 404A/TASK 27-21-41-991-004-A)
(a)
Apply the SPECIAL MATERIALS (Material No. 05-005) to the bolt (38).
(b)
Connect the servo actuator 2025GM (35) at RIB5.
1_ Install the bushes (47),(48) in the bracket (36).
2_ Put the sealing rings (49) in position on the piston arm
bearing of the servo actuator (35).
3_ Put the piston arm of the servo actuator (35) in position in
the bracket (36).
4_ Align the piston arm bearing of the servo actuator (35) with
the bolt hole in the bracket (36).
5_ Install the locking plate (39) and the washer (120) at the
bracket (36).
6_ Install the bolt (38) through the connection of the bracket
(36) and the piston arm of the servo actuator (35).
7_ Install the washer (110) and the nut (111).
R 1EFF : 004-049, 055-099, 101-149, 151-199, 1 27-21-41Page 442 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 8 TORQUE the nut (111) to 8.15 m.daN (60.10 lbf.ft).
_
9 Install the locking cap (112) and the cotter pin (113).
_
(c) Do the steps written above again and connect the servo actuators 3025GM (35) at RIB4 and 1025GM (35) at RIB3.
(18)
Apply a thin layer of the SPECIAL MATERIALS (Material No. 05-005) (Ref. TASK 51-75-13-916-002) to all the cadmium-plated steel parts of the rudder hinges which you can see.
(19)
Connect the push-rod (10) from the transducer 42WV (13) to the bracket (11) of the rudder (2) (Ref. Fig. 403/TASK 27-21-41-991-003)
(a)
Install the flanged bushes (18),(19) in the attachment bracket (14).
(b)
Cut and remove the temporary tie wraps, and release the push-rod
(10)
from the hinge arm (12).
(c)
Put the eye-end of the push-rod (10) in position at the attachment bracket (14).
(d)
Install the sliding bush (17) in the attachment bracket (14).
(e)
Install the bolt (16), the washer (20) and the nut (21) at the connection of the attachment bracket (14) and the push-rod (10).
(f)
Safety the nut (21) with a new cotter pin (22).
**ON A/C ALL
Subtask 27-21-41-080-050
E. Removal of the Hoisting Sling and the Rigging Pins
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵2(12)
