Location of Rigging Pins
Figure 401/TASK 27-23-17-991-002
1EFF : ALL 1 27-23-17 Page 405
1 1 Feb 01/98
1 1
1CES 1
Artificial Feel Unlocking Solenoid 16CA
Figure 402/TASK 27-23-17-991-001
1EFF : ALL 1 27-23-17 Page 406
1 1 Feb 01/98
1 1
1CES 1
R (d) Support the artificial feel unit (4).
(e) Remove the bush (10) from the lever arm (11).
R R (4) Disconnect the forked lever (17) of the artificial feel unit (4) from the solenoid 16CA (3).
(a) Remove the screws (7) and the washers (8) from the cover (6).
R (b) Remove the cover (6) from the artificial feel unit (4).
(c) Remove and discard the cotter pin (30).
(d) Remove the nut (29), the washer (28) and the bolt (15).
R (5) Remove the solenoid 16CA (3) from the artificial feel unit (4).
(a) Support the solenoid (3).
(b) Remove the screws (22) and the washers (23).
R R (c) Move the eye-end (18) of the solenoid (3) away from the forked lever (17) of the artificial feel unit (4).
(d) Remove the bush (16) from the forked lever (17).
(e) Remove the solenoid (3).
(6) Remove the eye-end (18) of the solenoid (3) from the screw spindle (21).
R R R R R R R CAUTION : BE CAREFUL WHEN YOU REMOVE THE PARTS THAT FOLLOW:_______ - THE EYE END - THE SHIM WASHER - THE SECURING PLATE - THE SCREW SPINDLE. IF YOU TURN THE SHAFT DURING THE REMOVAL OF THESE PARTS, DAMAGE TO THE SOLENOID CAN OCCUR.
(a) Straighten the tab of the securing plate (20) to release the eye-end (18).
R R (b) Hold the screw spindle (21) and turn the eye-end (18) in the counter-clockwise direction to release it.
(c) Remove and retain the eye-end (18).
(d) Remove and discard the shim washer (19) and the securing plate (20).
1EFF : ALL 1 27-23-17Page 408 1 1 May 01/05R 1 1 1CES 1
TASK 27-23-17-400-001
Installation of the Artificial Feel Unlocking Solenoid 16CA
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______
CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notices
No specific adjustable access platform 6.0 m (19 ft. 8 in.) R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft)
98D27207547000 1 PIN - RIGGING
98D27207548000 1 PIN - RIGGING
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵2(102)
