钻石40飞机维护手册 DA 40 SERIES AMM 4(18)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

% Every 28 days, Bendix/King receives new data base information. This information is downloaded % onto data base cards. The data base card is inserted in the slot on the left side of the GPS % receiver.
% There are three data base coverage areas available for the KLN 94. They are known as the % 'Americans' data base, the 'Atlantic' data base, and the 'Pacific' data base.
% The KLN 94 GPS receiver has these controls:
%) ON/OFF/brightness knob. It is used to turn the unit on and off and adjust display brightness.
%) Right outer knob. When the cursor is off, it is used to select the page type (for example, APT, % NAV, FPL, etc.). When the cursor is on, it is used to move the cursor on the display.
%) Right inner knob - When the cursor is off, it is used to select the specific page number for a % page type (for example, APT 1, APT 2, APT 3, etc.). When the cursor is on, it is used to select % alphanumerics or other applicable data for the field the cursor is on.
%) PROC (procedure) button. It is used to initiate the loading of approaches, arrival procedures, % and departure procedures. Also used to activate vector-to-final (VTF) for approaches when an % approach with 'Vectors' has been loaded into the active flight plan.
%) RNG (range) button. It is used to change the map scale if the map page (Nav 4) page is being % displayed. It is used to select the map page if it is not already on the map page.
%) MEN (menu) button. It is used to display the map menu if the map page (Nav 4) page is being % displayed. The map menu is used to initiate changing what is displayed on the map as well as % select the map orientation. It is used to select the map page if it is not already on the map page.
%) CRSR (cursor) button. It is used to turn the cursor on and off.
Doc # 6.02.01 Page 5
Rev. 4 09 Jan 2003

34-58-00
AMM

%) MSG (message) button. It is used to view messages.
%) OBS button. It is used to select between LEG mode and OBS modes.
%) ALT (altitude) button. It is used to select the two Altitude Pages where baro settings are made

% and VNAV operation is set up.

%) NRST (nearest) button. It is used to bring up a menu of nearest functions (Airports, VOR's,
% NDB's, intersections, etc.) that may be selected.
%) D

” (direct-to) button. It is used to initiate 'direct-to' operation (navigation from the present % position direct to the destination).
%) CLR (clear) button. It is used to delete data from a data field. It is also used to back up to a % previous step in some instances such as selecting approaches/STAR's/DP's.
%) ENT (enter) button. It is used to approve or acknowledge data.
Page 6 Doc # 6.02.01 09 Jan 2003 Rev. 4
34-58-00
Navigation
AMM

% C. Bendix/King KMD 150 Multifunction Display/GPS
% Figure 3 shows the Bendix/King KMD 150 Multifunction Display with an internal GPS receiver. It % is located in the avionics rack in the instrument panel, see Chapter 31.
% The avionics bus, or if installed, the essential avionics bus supplies power to the Multifunction % Display/GPS. The ALT/BAT switch and the AVIONICS MASTER switch must be set to ON to % supply power through the GPS circuit-breaker to the Multifunction Display/GPS. Refer to Chapter % 92 for the wiring diagrams.
% Every 28 days, Bendix/King receives new data base information. This information is downloaded % onto data base cards. The data base card is inserted in the slot on the bottom side of the % Multifunction Display/GPS.
% The KMD 150 Multifunction Display/GPS has the following controls:
%) ON/OFF/Brightness Control. It is used to turn the unit on and off and adjust display brightness.
%) Joystick. The joystick allows movement of the pointer in MAP mode and is used for all forms % of data entry or selection.
%) 5 Function Keys (Soft Keys). A label is drawn alongside each valid key. Whenever a new % function is selected, by pressing a valid key, a new screen is displayed along with its new key % labels. This capability of drawing key labels that are only applicable to a particular screen is % referred to as 'soft keying', and allows one key to perform multiple functions without the % complications of multiple key presses on an conventional keypad. Refer to the manufacturer's % manuals for mor information about the function keys.
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：钻石40飞机维护手册 DA 40 SERIES AMM 4(18)