钻石40飞机维护手册 DA 40 SERIES AMM 4(11)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

Turn the function selector switch clockwise from the OFF position to set the transponder on. There is a 45 second delay after setting the unit ON from OFF to let the transmitter tube warm-up. The function selector switch has these positions:
) SBY  Sets the transponder to the standby position. The transponder receives signals but does not transmit.
) ON  If the transponder receives a mode A interrogation, it transmits the mode A code set by the code selector knobs. You can set any code between 0000 and 7777.
) ALT  If the transponder receives a mode C interrogation, it transmits the altitude data from the blind encoder.
) TST  This uses a momentary contact switch to operate the transmitter. The reply lamp comes on. The reply lamp shows the operator that the unit is transmitting.
The reply lamp also shows when the IDENT button has been pressed. If you press the IDENT button once, the unit transmits a special identification pulse for each interrogation over the next 15 to 30 seconds.
Doc # 6.02.01 Page 3
Rev. 4 09 Jan 2003

34-56-00
AMM

Photocell provides Automatic Display Mode Dimming Annunciaton

Figure 2: Bendix/King KT 76C Transponder
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%

34-56-00
Navigation
AMM

C. Bendix/King KT 76C Transponder
Figure 2 shows the Bendix/King KT 76C transponder. It is located in the instrument panel on the % right side at the bottom, see Chapter 31.
The avionics bus or, if installed, the essential avionics bus supplies power to the transponder. The ALT/BAT switch and the AVIONICS MASTER switch must be set to ON to supply power through the XPDR circuit-breaker to the transponder. Refer to Chapter 92 for the wiring diagrams.
The transponder has a display which shows the following:
) Altitude window. The flight level altitude, marked by the letters 'FL' and a number in hundreds of feet, is shown on the left side of the display.
) Code window. The mode A code set by the code selector knobs is shown on the right side of the display.
) Reply indicator. The reply indicator blinks to indicate that the KT 76C is functioning properly and replying to interrogations.
The transponder has these controls:
) OFF/SBY/ON/ALT/TST function selector. Turn fully counter-clockwise to turn the transponder OFF. Turn the function selector switch clockwise to set the transponder ON. There is a 45 second delay after setting the unit ON from OFF to let the transmitter tube warm-up. The function selector switch has these positions:
) SBY. Sets the transponder to the standby position. The transponder receives signals but does not transmit.
) ON. If the transponder receives a mode A interrogation, it transmits the mode A code set by the code selector knobs. You can set any code between 0000 and 7777.
) ALT. If the transponder receives a mode C interrogation, it transmits the altitude data from the blind encoder.
) TST. Use this position to test the equipment.
) IDT (ident) button. Push this button momentarily to transmit a coded signal to Air Traffic Control. The unit will transmit a special identification pulse for each interrogation over the next 18 seconds. The 'reply' indicator will be displayed continuously during this time. You must only press this button at the request of Air Traffic Control.
Doc # 6.02.01 Page 5
Rev. 4 09 Jan 2003

34-56-00
AMM

) CODE selector knobs. Use these knobs to enter the mode A code.
) CLR button. Code entry mistakes are corrected, one digit at a time by pressing the CLR button and re-entering the correct code. The last active code will be displayed if a complete four-digit code has not been entered and there is no activity on any of the code entry buttons, the VFR button, or the CLR button for four seconds.
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：钻石40飞机维护手册 DA 40 SERIES AMM 4(11)