(2)
Remove the lining and the insulation of the cargo door to get access to the upper end of the gear box (Ref. TASK 52-31-13-000-001).
(3)
Remove the vent door cover from the internal door structure to get access to the actuator arm of the vent door.
4. Procedure
_________ R **ON A/C 001-049, 053-099, 101-105, 151-199, 201-220,
Subtask 52-31-21-020-051
A. Removal of the Gear Box Linkage R (Ref. Fig. 403/TASK 52-31-21-991-003)
(1)
Disconnect the drawbar (71) from the shaft lever (76) as follows:
(a)
Remove and discard the cotter pin (75) from the nut (74).
(b)
Remove the nut (74), the washers (73) and the bolt (72) from the shaft lever (76).
(c)
Remove the eye end of the drawbar (71) from the fork end of the shaft lever (76).
(2)
Disconnect the drawbar (71) from the actuator arm (107) of the vent door as follows:
(a)
Remove and discard the cotter pin (103) from the nut (104).
(b)
Remove the nut (104), the washers (105), the bush (106) and the bolt (108) from the actuator arm (107).
(c)
Remove the eye end of the drawbar (71) from the actuator arm (107).
(3)
Disconnect the connection rod (82) from the vent door lever (85) of the safety shaft as follows:
(a) Remove and discard the cotter pin (87) from the nut (86).
1EFF : ALL 1 52-31-21Page 420 1 1 May 01/05 1 1 1CES 1
Linkage of the Vent Door Mechanism R Figure 403/TASK 52-31-21-991-003
R 1EFF : 001-049, 053-099, 101-105, 151-199, 1 52-31-21Page 421 1201-220, 1May 01/05 1 1 1CES 1
(b)
Remove the nut (86), the washers (84) and the bolt (83) from the vent door lever (85).
(c)
Remove the lower eye end of the connection rod (82) from the fork end of the vent door lever (85).
(4)
Disconnect the connection rod (82) from the lever (80) as follows:
(a)
Remove and discard the cotter pin (77) from the nut (78).
(b)
Remove the nut (78), the washers (79) and the bolt (81) from the lever (80).
(c)
Remove the upper eye end of the connection rod (82) from the fork end of the lever (80).
(5)
Disconnect the link assy (88) from the target lever (90) as follows:
(a)
Remove and discard the cotter pin (91) from the nut (92).
(b)
Remove the nut (92), the washer (93), the sleeve (94) and the bolt (89) from the link assy (88).
(c)
Remove the fork end of the link assy (88) from the target lever (90).
(6)
Disconnect the link assy (88) from the drive shaft lever (102) as follows:
(a)
Remove and discard the cotter pin (96) from the nut (97).
(b)
Remove the nut (97) and the washer (98) from the drive shaft lever (102).
(c)
Remove the eye end of the link assy (88) from the drive shaft lever (102).
Subtask 52-31-21-020-068
B. Removal of the Gearbox R (Ref. Fig. 404/TASK 52-31-21-991-012)
(1) Disassemble the drive shaft lever (102) from the drive shaft of the gear box (123) as follows:
(a) Remove the nuts (128), the washers (127), the sleeves (126) and the tapered pins (125) from the lever (124).
R 1EFF : 001-049, 053-099, 101-105, 151-199, 1 52-31-21Page 422 1201-220, 1May 01/05 1 1 1CES 1
R Linkage of the Vent Door Mechanism
R Figure 403A/TASK 52-31-21-991-003-B
R 1EFF : 051-052, 1 52-31-21 Page 423
1 1 May 01/05
1 1
1CES 1
Linkage of the Vent Door Mechanism
Figure 403B/TASK 52-31-21-991-003-A
R 1EFF : 106-149, 221-299, 301-399, 401-499, 1 52-31-21Page 424 1 1 Aug 01/05 1 1 1CES 1
Gear Box of the Vent Door Mechanism R Figure 404/TASK 52-31-21-991-012
R 1EFF : 001-049, 053-099, 101-105, 151-199, 1 52-31-21Page 425 1201-220, 1May 01/05 1 1 1CES 1
(b)
Remove the nuts (133), the washers (132), the sleeves (126) and the tapered pins (129) from the safety cam (130).
(c)
Hold the safety cam (130) so that it does not fall down during the removal of the drive shaft lever (102).
(d)
Pull the drive shaft lever (102) from the cargo door frame and remove the safety cam (130).
(2)
Remove the shaft lever (76) from the output shaft of the gear box
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门4(91)
