R **ON A/C 001-049, 053-099, 101-105, 151-199, 201-220,
R Subtask 52-31-21-560-055-A
R B. Preparation for Replacement Component
R (1) Make sure that there are new tab washers (371) on the link assy (88).
R (2) If not, replace the tab washers (371) as follows:
R (a) Release the tab washers (371) from the jam nuts (372).
R (b) Remove the lower and top fork ends (95) and (99) from the
R connection rod (88).
R (c) Remove and discard the tab washers (371) from the connection rod
R (88).
R (d) Apply COMMON GREASE (Material No. 04-004) to the threaded ends of
R the connection rod (88).
R (e) Install new tab washers (371) and the two fork ends (95) and (99)
R on the connection rod (88).
R (3) Make sure that the length between the two fork ends (95) and (99) of
R the replacement link assy (88) is as written down before.
R Subtask 52-31-21-420-058-A
R C. Installation of the Switch Mechanism
R (Ref. Fig. 411/TASK 52-31-21-991-009)
R (1) Install the link assy (88) as follows:
R (a) Install the upper fork-end (99) on the drive shaft lever (102) as
R follows:
R 1 If removed, install the sleeve (100) into the fork-end (99)._
R 2 Put the fork end (99) in position to the drive shaft lever_
R (102) and install the bolt (101), the washer (98) and the nut
R (97).
R 3 Tighten the nut (97) and safety it with the new cotter pin_
(96).
R (b) Install the lower fork-end (95) to the target lever (90) as
R follows:
R 1_ If removed, install the bush (94) into the fork-end (95).
R 2_ Put the lower fork end (95) to the target lever (90) and
R install the bolt (89), the washer (93) and the nut (92).
R 3_ Tighten the nut (92) and safety it with the new cotter pin
(91).
R (2) Install the target lever (3) as follows:
R (a) If removed, install the target (365) with the bolts (366), the
R washers (363) and the nuts (362) on the target arm (364).
R (b) Install the target lever (90) as follows:
R 1_ Put the target lever (90) on the support fitting (361) and
R attach it with the washer (369) and the nut (368).
R 2_ Tighten the nut (368) and safety it with the new cotter pin
(367).
R (c) Install the lower fork end (95) to the target lever (90) (refer
R procedure (1) (b)).
R Subtask 52-31-21-820-054-A
R D. Adjustment Procedure
R (1) Push the door handle correctly into the recess of the door structure.
R (2) Measure the clearance between the target (365) and the related sensor
R (373) of the door sill area.
R NOTE : The clearance must be between 1.5 mm (0.0590 in.) and 2.0 mm____
(0.0787 in.).
R (3) If the clearance is out of tolerance, adjust the length of the link
R assy (88) as follows:
R (a) Turn the connection rod (370) until the clearance is correct.
R (b) Make sure that the connection rod (370) is correctly engaged with
R the lower and upper fork end (95) and (99).
R (c) Tighten the jam nuts (372) and safety them with the new tab
R washers (371).
R (4) Examine the correct function of the proximity switch 32WV (Ref. TASK
R 52-71-00-820-003).
R **ON A/C 051-052,
R Subtask 52-31-21-560-055
R B. Preparation for Replacement Component
R (1) Make sure that there are new tab washers (11) on the link assy (19).
R (2) If not, replace the tab washers (11) as follows:
R (a) Release the tab washers (11) from the jam nuts (12).
R (b) Remove the lower and top fork ends (10),(14) from the connection
R rod (13).
R (c) Remove and discard the tab washers (11) from the connection rod
R (13).
R (d) Apply COMMON GREASE (Material No. 04-004) to the threaded ends of
R the connection rod (13).
R (e) Install new tab washers (11) and the two fork ends (10),(14) on
R the connection rod (13).
R (3) Make sure that the length between the two fork ends (10),(14) of the
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门4(129)
