R 1EFF : 051-052, 1 52-31-21Page A418 1 1 May 01/05 1 1 1CES 1
R Teleflex Controls
R Figure 410A/TASK 52-31-21-991-011-A
R 1EFF : 051-052, 1 52-31-21 Page A419
1 1 May 01/05
1 1
1CES 1
R (4) Disconnect the lower ball joint (40) together with the eye end (37)
R from the ball bearing control (52) as follows:
R (a) Bend the tab washer (41) and loosen the lock nut (42).
R (b) Remove the lower ball joint (40), the tab washer (41) and the
R lock nut (42) from the control cable (52). Discard the tab
R washer.
R (c) Remove the seal nut (43) from the control cable (52).
R (5) If necessary, remove the eye ends (18),(37) from the ball joints
R (67),(40) as follows:
R (a) Bend the tab washers (69),(38) and loosen the lock nuts
R (68),(39).
R (b) Remove the eye ends (18),(37), the tab washers (69),(38) and the
R lock nuts (68),(39) from the ball joints (67),(40). Discard the
R tab washers.
R (6) Remove the ball bearing control (52) from the cargo door as follows:
R (a) Cut and remove the lockwire from the lock nuts
R (61),(60),(57),(56),(51),(50),(47) and (46) and the related
R brackets.
R (b) Remove the lock nuts (61),(60) and the washer (59) from the upper
R end of the ball bearing control (52).
R (c) Move the upper end of the ball bearing control (52) through the
R frame hole at FR27.
R (d) Remove the washer (58), the lock nuts (57),(56) from the upper
R end of the ball bearing control (52).
R (e) Move the ball bearing control (52) together with the grommet (55)
R through the frame hole at FR26A.
R (f) Remove the grommet (55) from the ball bearing control (52).
R (g) Move the lock nuts (46),(47) and the washer (48) from the lower
R end of the ball bearing control (52).
R (h) Move the lower end of the ball bearing control (52) through the
R frame hole of the longeron 4.
R 1EFF : 051-052, 1 52-31-21Page A420 1 1 May 01/05 1 1 1CES 1
(i)
Remove the washer (49), the lock nuts (50),(51) from the lower end of the ball bearing control (52).
(j)
Remove the screw (53) and disconnect the clamp (54) from the bracket of the longeron 3.
(k)
Remove the ball bearing control (52) through the cutout at the longeron 3 from the cargo door.
(l) Remove the clamp (54) from the ball bearing control (52). R **ON A/C 106-149, 221-299, 301-399, 401-499,
Subtask 52-31-21-020-064-A
A. Removal of the Drift Pin Assembly
(Ref. Fig. 409B/TASK 52-31-21-991-008-A)
(1)
Remove and discard the cotter pin (1) from the nut (2).
(2)
Remove the nut (2), the washers (3) and (5) and the bolt (7) to disconnect the drift pin (8) from the linkage (6).
(3)
Move the drift pin (8) out of the edge member bearing (9).
(4)
If necessary, remove the bush (4) from the fork end of the drift pin (8).
Subtask 52-31-21-020-065-A
B. Removal of the Linkage Assembly
(Ref. Fig. 409B/TASK 52-31-21-991-008-A)
NOTE : The linkage assembly includes the horizontal connection rods (28),
____
(29) and (42) and the vertical control rod (35).
(1) Remove the horizontal connection rod (28) as follows:
(a) Disconnect the rod-end from the bellcrank lever (37) as follows: 1 Remove and discard the cotter pin (27) from the nut (26).
_
2 Remove the nut (26), the washers (25) and the bolt (24).
_
3 Remove the horizontal connection rod (28) from the bellcrank
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门4(118)
