5. Close-up
________
Subtask 52-31-22-865-052
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1MJ, 3801GX, 3802GX, 3803GX
Subtask 52-31-22-410-050
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Make sure that the springs of the hinge arms are correctly lubricated (Ref. TASK 12-22-52-640-002).
(3)
Apply STORAGE PRESERVATION (Material No. 15-005) to all the components of the vent door and to the adjacent cargo door structure.
(4)
Install the removed parts of the lining and insulation (Ref. TASK 52-31-13-400-001).
(5)
Remove the actuator safety locks and close the FWD cargo door (Ref. TASK 52-30-00-860-002).
(6)
Remove the access platform(s).
1EFF : ALL 1 52-31-22Page 416 1 1 May 01/05 1 1 1CES 1
HARNESS - CARGO COMPARMENT DOOR - REMOVAL/INSTALLATION
______________________________________________________ TASK 52-31-24-000-001 Removal of the Wiring Harness 4611VB
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific access platform 3.5 m (11 ft. 6 in.)
98D52307515000 1 SAFETY LOCK - ACTUATOR, CARGO DOORS
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the
Yellow Electric Pump 52-31-13-000-001 Removal of the Lining and the Insulation 52-31-24-991-001 Fig. 401
3. Job Set-up
__________ Subtask 52-31-24-010-050
A. Get Access
(1)
Open the FWD cargo compartment door (referred to as cargo door) (Ref. TASK 52-30-00-860-001) and safety it with the SAFETY LOCK -ACTUATOR, CARGO DOORS (98D52307515000).
(2)
Put the access platform in position below the opened cargo door.
1EFF : ALL 1 52-31-24Page 401 1 1 Feb 01/99 1 1 1CES 1
(3) Remove the lining and insulation of the cargo door to get access to the terminal block 7526VT (Ref. TASK 52-31-13-000-001).
Subtask 52-31-24-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU HYDRAULIC/HYD POWER/Y 3803GX N30 122VU DOORS/CARGO 1MJ T12 123VU Y HYD/ELEC/PUMP 3802GX AB06 123VU Y HYD/ELEC/ELEC PUMP/NORM 3801GX AB03
4. Procedure
_________ Subtask 52-31-24-020-050
A. Removal of the Wiring Harness 4611VB
(Ref. Fig. 401/TASK 52-31-24-991-001)
(1)
Disconnect the connector (29) from the receptacle (28).
(2)
Put blanking caps on the disconnected electrical connectors.
(3)
Disconnect the electrical cables of the wiring harness (1) from the terminal block (6).
(4)
Remove the nut (3), the bolt (5) and the clamp (4) from the door angle (2).
(5)
Remove the nut (12), the washer (11), the bolt (9) and the clamp (8) from the actuator fitting bracket (10).
(6)
Remove the nut (14) and the washer (15) from the bolt (17) and disconnect the clamp (16) from the bracket (18) in the actuator area.
(7)
Cut and remove the tie-raps (26) and disconnet the wiring harness (1) from the cable brackets (27) of the ceiling lining.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门4(156)
