(b)
Move the door handle down and push it into the recess of the door structure.
(2)
Measure the lateral gap "A" between the door handle and the door structure.
NOTE : The lateral gaps "A" should have the same size and must be
____ between 1.0 mm (0.0393 in.) and 3.0 mm (0.1181 in.).
(3) If the lateral gaps "A" are out of tolerance,change the position of the door handle as follows:
(a) Remove the screws (119) and (120), the washers (118) and the access cover (117) from the inboard of the cargo door.
1EFF : ALL 1 52-31-11Page 518 1 1 Aug 01/05 1 1 1CES 1
Adjustment of the Door Handle
Figure 503/TASK 52-31-11-991-009
R 1EFF : 001-049, 053-099, 101-105, 151-199, 1 52-31-11Page 519 1201-220, 1May 01/05 1 1 1CES 1
R Adjustment of the Locking Handle
R Figure 503A/TASK 52-31-11-991-009-B
R 1EFF : 051-052, 1 52-31-11 Page 520
1 1 May 01/05
1 1
1CES 1
Adjustment of the Door Handle Figure 503B/TASK 52-31-11-991-009-A
R 1EFF : 106-149, 221-299, 301-399, 401-499, 1 52-31-11Page 521 1 1 Aug 01/05 1 1 1CES 1
(b)
Remove the screws (112) and lock device (113) from the door structure.
(c)
Install a mounting nut (e.g. NAS 509-4) on the spring bolt to keep the handle spring in position.
(d)
Carefully remove the door handle shaft (114) and change the position and/or the quantity of the adjustment washers (115) and (116).
(e)
Assemble the door handle shaft (114) and the adjustment washers
(115) and (116) on the door structure.
(f)
Make sure that the lateral gaps "A" are correctly adjusted.
(g)
Safety the door handle shaft (114) with the lock device (113) and the screws (112).
(h)
Remove the mounting nut from the spring bolt.
(4) Adjust the offset "B" of the door handle as follows:
(a) Make sure that the door handle is in line with the cargo door structure.
NOTE : It is allowed that the door handle is out of wind for max.
____
1.0 mm (0.0393 in.)
(b)
If the offset is out of tolerances, move the door handle up to the UNLOCKED position.
(c)
Loosen the nut (111) and turn the stop bolt (110) as required.
(d)
If the offset "B" is correct, tigthen the nut (111).
(5)
Put the access panel (117) in position to the inner skin of the cargo door and attach it with the screws (119) and (120) and the washers (118).
(6)
Move the door handle into the fully UNLOCKED position.
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-31-11Page 522 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Subtask 52-31-11-820-053
R B. Adjustment of the Skin Offset at the Door Handle
**ON A/C 001-049, 053-099, 101-105, 151-199, 201-220,
(Ref. Fig. 504/TASK 52-31-11-991-010)
R **ON A/C 106-149, 221-299, 301-399, 401-499,
(Ref. Fig. 504B/TASK 52-31-11-991-010-A)
R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
R R (1) Measure the skin offset "C" between the door handle (128) and the access panel (127).
NOTE : The skin offset "C" must be between 0.3 mm (0.0118 in.) and____ 0.7 mm (0.0275 in.).
R R (2) If the skin offset "C" is not in the limits, adjust the position of the catch hook (125) as follows:
(a) Remove the screws (124), the catch hook (125) and the shim (126) from the structure fitting (121).
R R (b) Prepare the shim (126) as required until the skin offset "C" is correct.
(c) Attach the catch hook (125) and the shim (126) with the screws (124) on the structure fitting (121).
R (d) Make sure that the skin offset "C" is correctly adjusted.
Subtask 52-31-11-820-054
C. Adjustment of the Latching Mechanism
**ON A/C 001-049, 053-099, 101-105, 151-199, 201-220,
(Ref. Fig. 505/TASK 52-31-11-991-011)
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 52-31-11Page 523 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Adjustment of the Handle Flap
Figure 504/TASK 52-31-11-991-010
R 1EFF : 001-049, 053-099, 101-105, 151-199, 1 52-31-11Page 524 1201-220, 1May 01/05 1 1 1CES 1
R Adjustment of the Handle Flap
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门4(53)
