____ check and assemble the compenents of the HOIST - MINILIFT.
(3)
Install the HOIST - MINILIFT to the APU compartment.
(a)
Remove the temporarily installed quick release pins (2) and (8) from the HOIST - MINILIFT.
(b)
Put the HOIST - MINILIFT (10) in the correct position and attach it with the quick release pin (2) to the APU hoist bracket (1) on the top firewall of the APU compartment.
(c)
Put the HOIST - MINILIFT in the correct position and attach it with the quick release pin (8) to the bearing assy (7) on the LH side of the APU compartment.
(4)
Connection the of the HOIST - MINILIFT cable to the APU
(a)
Connect the shackle (5) to the cable (3) of the HOIST - MINILIFT with the quick release pin (4).
(b)
Connect the shackle (5) with the quick release pin (6) to the adapter of the APU (9).
(5)
Put the weight of the APU from the APU mounts onto the HOIST -MINILIFT.
APU Hoist Minilift Installation
Figure 202/TASK 49-00-00-991-008
CES
CAUTION : DO NOT TURN THE HOIST HANDLE MORE THAN 90 DEGREES, AFTER
_______ YOU REMOVE THE SLACK FROM THE HOIST CABLE. IF YOU TURN THE HOIST HANDLE MORE THAN 90 DEGREES, YOU CAN CAUSE DAMAGE TO THE APU AND THE APU MOUNTS.
(a) Operate the HOIST - MINILIFT (10) until the weight of the APU is removed from the APU mounts.
NOTE : Do a check and make sure that the HOIST - MINILIFT is
____ assembled and installed correctly and holds the load.
NOTE : Before you install the hoist handle, turn the upper drum
____ shaft of the HOIST - MINILIFT with your hand until you have removed the slack from the hoist cable. Then install the hoist handle on the upper drum shaft and turn the handle 90 degrees in a clockwise direction. Thus you make sure that the weight of the APU is removed from the APU mounts.
TASK 49-00-00-080-001
Removal of the APU Hoist Tool (APS 3200)
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 3.5 m (11 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
from the External Power 29-10-00-864-001 Depressurize the Green Hydraulic System 29-10-00-864-002 Depressurize the Yellow Hydraulic System 29-10-00-864-003 Depressurize the Blue Hydraulic System 49-11-11-400-003 Installation of the Power Plant (APU) (APS 3200) 49-52-41-000-002 Removal of the Oil Cooler Outlet Duct (APS 3200) 49-52-41-400-002 Installation of the Oil Cooler Outlet Duct (APS 3200) 52-41-00-010-001 Open the APU Doors for Access 52-41-00-410-001 Close the APU Doors after Access 52-41-21-000-001 Removal of the APU Access Door 315AL 52-41-21-400-001 Installation of the APU Access Door 315AL 49-00-00-991-008 Fig. 202
3. Job Set-up
__________ Subtask 49-00-00-860-053
A. Aircraft Maintenance Configuration
(1)
Make sure that the warning notices are on panel 25VU to tell persons not to start the APU.
(2)
Make sure that the ground service network is energized (Ref. TASK 24-41-00-861-002).
(3)
Make sure that the hydraulic systems are depressurized (Ref. TASK 29-10-00-864-001), (Ref. TASK 29-10-00-864-002) and (Ref. TASK 29-10-00-864-003).
(4)
Make sure that the access platform is in position below the access doors 315AL and 316AR.
(5)
Make sure that the APU access doors 315AL, 316AR are open (Ref. TASK 52-41-00-010-001) or removed (Ref. TASK 52-41-21-000-001).
NOTE : The installation of the HOIST - MINILIFT is also possible
____ without a removal of the APU access door 315AL, but a removal will make the installation of the HOIST - MINILIFT easier.
(6)
Make sure that the light switch 11LJ is set to on.
(7)
Make sure that the the oil-cooler outlet duct is removed (Ref. TASK 49-52-41-000-002).
Subtask 49-00-00-865-083
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged 1KD, 2KD, 1WF, 2WF, 3WF, 4WF.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM 机载辅助动力 AIRBORNE AUXILIARY POWER1(109)
