A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵7(92)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 Subtask 27-84-00-865-052
 D. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/WTB/SLT/SYS2 11CV P19 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21 122VU FLIGHT CONTROLS/WTB/SLT/SYS1 9CV S06
 4. Procedure_________
 Subtask 27-84-00-710-050 
R  A. Operational Test of the Slat System
 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE. 
R R R R  CAUTION : IF THE THRUST REVERSER COWLS ARE OPEN, MAKE SURE THAT THE HALF_______ DOORS OF THE THRUST REVERSER ARE RETRACTED BEFORE YOU EXTEND THE SLATS. IF THE DOORS ARE EXTENDED, YOU CAN CAUSE DAMAGE TO THE SLATS AND HALF DOORS WHEN THE SLATS EXTEND.
 (1) Electronic Centralized Aircraft Monitoring
 (a) Set the ECAM system to ON (Ref. TASK 31-60-00-860-001).

 

 (2) Do this test:
 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the center pedestal on the panel 114VU: 
R R R R R R R R  - move the slat and flap control lever to the position 1 and then to the position 2. Stop at each notch until the slats are in their new position. 
2. On the panel 114VU: 
R R  - move the slat and flap control lever to the position 3.
R R R 
3. On the panel 114VU: 
R R  - move the slat and flap control lever to the position FULL.
R R R R R 
4. On the panel 114VU: 
R R  - move the slat and flap control lever back to the position 3.
R R 

-
the slats move to the set position.

On the ECAM upper DU:

-
the slat position bar moves to the set position

-
the new position of the lever and the travel direction of the slats are shown.

-
the slats do not move.

 On the ECAM upper DU:

-
the slat position bar does not move

-
the new position of the lever is shown as above.

-
the slats move to the set position.

 On the ECAM upper DU:

-
the slat position bar moves to the set position

-
the new position of the lever and the travel direction of the slats are shown.

-
the slats move to the set position.

 On the ECAM upper DU:

-
the slat position bar moves to the set position

 

 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
R R R R R 
5. On the panel 114VU: 
R R  - move the slat and flap control lever back to the position 2.
R R R 
6. On the panel 114VU: 
R R R R R R R R R R  - move the slat and flap control lever back to the positions 1 and 0. Stop at each notch until the slats are in their new position. 
5. Close-Up________
 Subtask 27-84-00-860-053

-the new position of the lever and the travel direction of the slats are shown
-no warnings related to the slat system are shown.
-
the slats do not move.

 On the ECAM upper DU:

-
the slat position bar does not move

-
the new position of the lever is shown.

-
the slats move to the set position.

On the ECAM upper DU:

-
the slat position bar moves to the set position

-
the new position of the lever and the travel direction of the slats are shown

-no warnings related to the slat system are shown.
 A. Aircraft Maintenance Configuration
 (1)
 Depressurize the Blue hydraulic system
 (Ref. TASK 29-10-00-864-003).

 (2)
 On the ECAM control panel, set the control/brightness controls to OFF.

 (3)
 De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).

 

 Subtask 27-84-00-865-051
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV, 14CC1, 14CC2.
 Subtask 27-84-00-942-050
 C. Removal of Equipment
 (1)
 Remove the safety barriers.

 (2)
 Remove the warning notice(s).

 (3)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵7(92)