3. Job Set-up__________
Subtask 27-81-00-941-059
A. Safety Precautions
(1) Put the safety barriers in position.
(2) Put a warning notice in the cockpit to tell persons not to operate the slat system.
4. Procedure_________
R
Subtask 27-81-00-865-070
R A. Open, safety and tag this(these) circuit breaker(s):
R R -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
Subtask 27-81-00-040-050
R B. Deactivation of the SFCC 2 WTB Solenoids
(1) Do a test to make sure that the channel 1 of the wing tip brakes is serviceable (Ref. TASK 27-81-00-710-001).
(2) Put the warning notice in the cockpit to tell the flight crew that one or two of the SFCC 2 slat WTB solenoids are deactivated.
(3) Make an entry in the aircraft technical logbook to record the deactivation of the SFCC 2 slat WTB solenoids.
R Subtask 27-81-00-865-073
R R R C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 7CV, 8CV
5. Close-up
________ Subtask 27-81-00-942-056
A. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 27-81-00Page 403 1 1 Nov 01/02R 1 1 1CES 1
TASK 27-81-00-440-001 Reactivation of the SFCC 2 Slat WTB Solenoids WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Refer to the MMEL TASK: 27-81-01
Slats Electrical Control and Monitoring
Slat Wing Tip Brakes Solenoids
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R TSM 27 PB 101 (for corrective action)
3. Job Set-up
__________
Subtask 27-81-00-941-056
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice in the cockpit to tell persons not to operate
the slat system. R
4. Procedure
_________ R Subtask 27-81-00-440-050 R A. Reactivate the SFCC 2 Slat WTB Solenoids
(1)
Do the trouble-shooting of the WTB solenoids and do the applicable correction(s) (Ref. TSM 27 PB 101).
(2)
Make an entry in the aircraft technical logbook to record the reactivation of the SFCC 2 WTB solenoids.
5. Close-up
________
Subtask 27-81-00-942-057
A. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
SLATS ELECTRICAL CONTROL AND MONITORING - ADJUSTMENT/TEST
_________________________________________________________
TASK 27-81-00-740-001
Read-out for Class 3 Faults in the Slat System
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
- 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵7(58)
