R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 02-003 F NSA 307110 TYPE 4
HYDRAULIC FLUID (PHOSPHATE ESTER BASE)
(Ref. 20-31-00)
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
1 O-ring 27-51-51 01 -090 2 back-up ring 27-51-51 01 -070 3 O-ring 27-51-51 01 -080 4 back-up ring 27-51-51 01 -060 5 O-ring 27-51-51 01 -040 6 O-ring 27-51-51 01 -050
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
12-12-29-611-001 Fill the Hydraulic Fluid Reservoir with a Hand Pump 12-12-29-611-002 Fill the Hydraulic Fluid Reservoir with a Hydraulic
Service Cart
27-80-00-866-005 Retracting the Slats on the Ground
27-81-00-710-001 Operational Test of the Wing-Tip Brake and the
Pressure-Off Brake
29-10-00-863-001 Pressurize the Green Hydraulic System
R 29-10-00-863-003 Pressurize the Blue Hydraulic System with a Ground
R Power Supply 29-10-00-864-001 Depressurize the Green Hydraulic System 29-10-00-864-003 Depressurize the Blue Hydraulic System 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 27-81-51-991-002 Fig. 402
3. Job Set-up
__________
Subtask 27-81-51-941-062
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the warning notice is in position to tell persons not to operate the slat controls.
(3)
Make sure that the warning notice is in position to tell persons not to pressurize the hydraulic systems.
Subtask 27-81-51-860-057
B. Aircraft Maintenance Configuration
R (1) Make sure that the access platform is below the applicable zone R 522(622).
(2)
Make sure that the applicable access panel has been removed:
-
for the solenoid valve (7) on 35CV, remove 522SB
-
for the solenoid valve (7) on 36CV, remove 622SB.
(3)
Make sure that the slats are fully retracted (Ref. TASK 27-80-00-866-005).
(4)
Make sure that the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER is on the flap/slat control lever on panel 114VU.
(5)
Make sure that the Blue and Green hydraulic systems are depressurized (Ref. TASK 29-10-00-864-003) and (Ref. TASK 29-10-00-864-001).
(6)
Make sure that the Blue and the Green hydraulic reservoirs are depressurized (Ref. TASK 29-14-00-614-001).
Subtask 27-81-51-865-054
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU FLIGHT CONTROLS/WTB/SLT/SYS2 11CV P19 122VU FLIGHT CONTROLS/WTB/SLT/SYS1 9CV S06
4. Procedure
_________
(Ref. Fig. 402/TASK 27-81-51-991-002)
Subtask 27-81-51-420-055
A. Preparation for Installation
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1)
Clean the component interface and/or the adjacent area with a clean MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-004).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵7(82)
