TASK 27-80-00-866-005
Retracting the Slats on the Ground
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
R
1. Reason for the Job
__________________
To retract the slats without movement of the flaps. To retract the slats and flaps at the same time (Ref. TASK 27-50-00-00901).
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific safety barriers
No specific warning notice(s)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power 29-10-00-863-003 Pressurize the Blue Hydraulic System with a Ground
Power Supply
29-10-00-864-003 Depressurize the Blue Hydraulic System
31-60-00-860-001 EIS Start Procedure
3. Job Set-Up
__________ Subtask 27-80-00-941-053
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put the warning notice(s) in position to tell persons that the slat system is in operation.
Subtask 27-80-00-865-057
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 49VU AUTO FLT/FAC1/26VAC 14CC1 B03 121VU AUTO FLT/FAC2/26VAC 14CC2 M18 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
Subtask 27-80-00-860-054
C. Aircraft Maintenance Configuration
(1)
Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
(2)
Pressurize the Blue hydraulic system
(Ref. TASK 29-10-00-863-003).
NOTE : The Blue and/or Green hydraulic system(s) operate(s) the slat
____ system. If necessary, use the alternative hydraulic system.
NOTE : If you use the Blue Hydraulic System, an ECAM S/CTL SLAT SYS 2
____ FAULT message will show. This message can be ignored.
NOTE : If you use the Green Hydraulic System, an ECAM S/CTL SLAT SYS
____ 1 FAULT message will show. This message can be ignored.
(3) Set the ECAM system to on (Ref. TASK 31-60-00-860-001).
1EFF : ALL 1 27-80-00Page 212 1 1 Aug 01/05R 1 1 1CES 1
Subtask 27-80-00-865-058
D. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/WTB/SLT/SYS2 11CV P19 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21 122VU FLIGHT CONTROLS/WTB/SLT/SYS1 9CV S06
4. Procedure
_________ Subtask 27-80-00-866-053
A. Retraction of the Slats on the Ground WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER.
(2)
Set the slat/flap control lever to position 0.
(3)
Make sure that on the ECAM upper DU the slat position bar moves to the correct position.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵7(38)
