R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 02-003 F NSA 307110 TYPE 4
HYDRAULIC FLUID (PHOSPHATE ESTER BASE)
(Ref. 20-31-00)
Material No. 04-018
GENERAL PURPOSE ASSEMBLY PASTE (Ref. 20-31-00)
Material No. 04-022 USA MIL-PRF-81322 GRADE 2
SYNTHE.HYDROCARBON GREASE HIGH PRESSURE
(Ref. 20-31-00)
Material No. 05-020 USA MIL-L-60326 TYPE I
FLUOROCARBON RELEASE AGENT (Ref. 20-31-00)
Material No. 09-001 USA MIL-S-8802 TYPE I CLASS A
FUEL TANK SEALANTPOLYSULFIDE (Ref. 20-31-00)
Material No. 09-018 USA AMS 3267/3
CORROSION INHIBITING LOW ADHESION SEALANT
(Ref. 20-31-00)
-------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 09-019 USA AMS 3267/3 LOW ADHESION CORROSION INHIBITING SEALANT
Material No. 11-026 Material No. 15-007 (Ref. 20-31-00)GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00)AIB TN 10138 TYPE II GRADE 1
CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND
Material No. 19-003 (Ref. 20-31-00)USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
11 O-ring 29-12-05 24 -060
14 O-ring 27-84-05 58 -070
23 O-ring 27-84-05 58 -070
28 O-ring 29-11-05 05 -060
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-12-29-611-001 12-12-29-611-002 Fill the Hydraulic Fluid Reservoir with a Hand PumpFill the Hydraulic Fluid Reservoir with a Hydraulic Service Cart
20-28-00-912-004 27-50-00-000-003 27-50-00-400-003 27-80-00-866-005 Electrical Bonding of Components With Conductive Bolts and Screws and Bonding Straps in the Fuselage and in the Wings (this does not include the tanks)-Removal of the Lock-Torque Shaft - Flaps and Slats (98D27504030001)Installation of the Lock-Torque Shaft - Flaps and Slats (98D27504030001)Retracting the Slats on the Ground
1EFF : ALL 1 27-81-51Page 408 1 1 May 01/05R 1 1 1CES 1
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-81-00-710-001 Operational Test of the Wing-Tip Brake and the
Pressure-Off Brake
27-84-45-400-007 Installation of the Torque Shafts 6014CM(6064CM)/6028CM(6078CM)/6036CM (6086CM)/6038CM(6088CM)/6040CM(6090CM)/6042CM(6092CM) /6044CM(6094CM)
29-10-00-863-001 Pressurize the Green Hydraulic System
R 29-10-00-863-003 Pressurize the Blue Hydraulic System with a Ground
R Power Supply 29-10-00-864-001 Depressurize the Green Hydraulic System 29-10-00-864-003 Depressurize the Blue Hydraulic System 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 27-81-51-991-001 Fig. 401
3. Job Set-up
__________
(Ref. Fig. 401/TASK 27-81-51-991-001)
Subtask 27-81-51-941-061
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the warning notice(s) is/are in the cockpit to tell persons not to operate the slat controls.
(3)
Make sure that the warning notice(s) are in position to tell persons not to pressurize the hydraulic systems.
Subtask 27-81-51-860-055
B. Aircraft Maintenance Configuration
(1)
Make sure that the access platform is below the applicable access panel.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵7(78)
