A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵7(136)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 (6) Apply a layer of STORAGE PRESERVATION (Material No. 15-007) to: - the nuts (2) - the bolts (4) - the flanges of the universal joints (1) and (5) - the flanges of the shaft (3). 
R  (7) Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT (Ref. TASK 27-50-00-400-003): - from the torque shaft, outboard of the applicable component - from the torque shaft, inboard of the applicable component.
 Subtask 27-84-45-210-058
R  C. Dimensional/Visual Check (Ref. Fig. 402/TASK 27-84-45-991-002) 
R R R R R  (1) Make sure that: - you cannot see the spline engagement groove at the movable joint - the dimension A is a minimum of 6.5 mm (0.2559 in.) at the movable joint.

 

R
 Subtask 27-84-45-865-065
 D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CV, 7CV.
 Subtask 27-84-45-710-052
 E. Test 
R R  (1) Do an operational test of the slat power-transmission system (Ref. TASK 27-84-00-710-001). Make sure that the rotation of the torque shafts does not cause damage.
 5. Close-up________ 
R  (Ref. Fig. 401/TASK 27-84-45-991-001)
 Subtask 27-84-45-865-066
 A. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
 Subtask 27-84-45-410-052
 B. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
R R  (2) Install the applicable access panels: - FOR 6010CM install 191BT and 521AB - FOR 6060CM install 192BT and 621AB.

 

 Subtask 27-84-45-865-067
 C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CV, 7CV.
 Subtask 27-84-45-942-053
 D. Removal of Equipment
 (1)
 Remove the safety barriers.

 (2)
 Remove the warning notice(s).

 (3)
 Remove the access platform(s).

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 1EFF : ALL 1 27-84-45Page 438 1 1 Feb 01/00R 1 1 1CES 1

 TASK 27-84-45-000-005
R Removal of the Torque Shaft 6012CM(6062CM)
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notice No specific access platform 2.8 m (9 ft. 2 in.) 98D27504030001 1 LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-400-003 Installation of the Lock-Torque Shaft - Flaps and
 Slats (98D27504030001)
 27-80-00-866-005 Retracting the Slats on the Ground
 27-84-45-991-001 Fig. 401
 27-84-45-991-003 Fig. 403

 

 3. Job Set-up
__________ (Ref. Fig. 401/TASK 27-84-45-991-001) Subtask 27-84-45-941-053
 A. Safety Precautions
 (1)
 Put the safety barriers in position.

 (2)
 Put a warning notice in position to tell persons not to operate the slat controls.

 Subtask 27-84-45-860-068
 B. Aircraft Maintenance Configuration
 (1)
 Retract the slats fully (Ref. TASK 27-80-00-866-005).

 (2)
 Make sure that the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) is on the flap/slat control lever on panel 114VU.

 Subtask 27-84-45-865-053
 C. Open, safety and tag this(these) circuit breaker(s):
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵7(136)