(2)
Make sure that the clearance 'V' is between 16 mm (0.6299 in.) and 20 mm (0.7874 in.).
(3)
Make sure that the clearance 'X' is between 5 mm (0.1968 in.) and 8 mm (0.3149 in.).
(4)
Make sure that the clearance 'Z' is between 1.63 mm (0.0641 in.) and
2.82 mm (0.1110 in.). The spoiler and the structure must make a continuous surface. The seal must touch the trailing edge structure along its full length.
(5)
Pressurize the Green hydraulic system
(Ref. TASK 29-10-00-863-001).
(6)
Adjust the spoiler to give the dimension 'U' between the spoiler and the flap (Ref. TASK 27-64-00-820-001).
Subtask 27-64-45-410-050
J. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the access panels (Ref. TASK 57-51-37-400-004):
-
for the left wing, install 575GB
-
for the right wing, install 675GB.
(3)
To remove the safety collar CAUTION : SUPPORT THE SERVO CONTROL 7.5kg (16.5lb) AND THE SPOILER
_______ APPROXIMATELY 15kg (33lb). THIS WILL PREVENT DAMAGE TO:
-
THE HYDRAULIC LINES
-
THE ELECTRICAL CABLES
-
THE STRUCTURE.
(a) Remove the COLLAR-SAFETY, SPOILER.
(4) Remove the access platform(s). Subtask 27-64-45-865-054
K. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV, 21CE1, 21CE2, 21CE3.
Subtask 27-64-45-710-050
L. Operational Test
(1) Do an operational test of the spoiler (Ref. TASK 27-64-00-710-001).
5. Close-up
________ Subtask 27-64-45-942-051
A. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
SPOILER 5 - INSPECTION/CHECK
____________________________ TASK 27-64-45-200-001 Inspection/Check of the Spoiler 5 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1.
Reason for the Job
__________________
Because the free movement is more than that in TASK 27-64-00-200-001.
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice
1EFF : ALL 1 27-64-45Page 601 1 1 Feb 01/03R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-64-45-000-001 Removal of the Spoiler 5
27-64-45-400-001 Installation of the Spoiler 5
**ON A/C 001-003, 051-052,
27-64-45-991-003 Fig. 601 R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
27-64-45-991-003-A Fig. 601A
**ON A/C ALL
3. Job Set-up
__________
Subtask 27-64-45-941-055
A. Safety Precautions 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵7(6)
