曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
To change the altitude buffer distance setting:
1) While on the System Setup Page, press the FMS Knob momentarily to activate the flashing cursor.
2) Turn the large FMS Knob to highlight the altitude buffer field in the Airspace Alerts Box.
3) Turn the FMS Knobs to enter an altitude buffer value and press the ENT Key.
To turn an airspace alert on or off:
1) While on the System Setup Page, press the FMS Knob momentarily to activate the flashing cursor.
2) Turn the large FMS Knob to highlight the desired field in the Airspace Alerts Box.
3) Turn the small FMS Knob clockwise to turn the airspace alert ON or counterclockwise to turn the alert OFF.
A
udud
i
o Alerts
The Audio Alert Box on the System Setup Page allows the audio alert voice to be set to male or female.
To change the audio alert voice:
1) While on the System Setup Page, press the FMS Knob momentarily to activate the flashing cursor.
2) Turn the large FMS Knob to highlight the voice in the Audio Alert Box.
3) Turn the small FMS Knob to display and highlight the desired voice and press the ENT Key.
Flight Director
Two formats are available for the display of the flight director. Single Cue or X-Pointer may be selected.
To change the flight director format:
1) While on the System Setup Page, press the FMS Knob momentarily to activate the flashing cursor.
2) Turn the large FMS Knob to highlight the Format Active field in the Flight Director Box.
3) Turn the small FMS Knob to display and highlight the desired flight director format and press the ENT Key.
190-00494-02 Rev. B Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 37
System ystem Overview verview
SYSTEM
OVERVIEW
FLIGHT
INSTRUMENTS EICAS AUDIO PANEL
& CNS
FLIGHT
MANAGEMENT
HAZARD
AVOIDANCE AFCS ADDITIONAL
FEATURES APPENDICES INDEX
FD Data Bar Fields
The MFD Data Bar Fields Box on the System Setup Page displays the current configuration of the MFD Navigation Status Box. By default, the Navigation Status Bar is set to display ground speed (GS), desired track (DTK), track (TRK), and estimated time enroute (ETE).
To change the information shown in an MFD Navigation Status Bar field:
1) While on the System Setup Page, press the FMS Knob momentarily to activate the flashing cursor.
2) Turn the large FMS Knob to highlight the desired field number in the MFD Data Bar Fields Box.
3) Turn the small FMS Knob to display and scroll through the data options list and press the ENT Key when the desired data selection is highlighted.
The following data may be selected for display in each of the four fields of the Navigation Status Box.
• Bearing (BRG)• Distance (DIS)• Desired Track (DTK)• En Route Safe Altitude (ESA)• Estimated Time of Arrival (ETA)• Estimated Time En Route (ETE)• Ground Speed (GS)• Minimum Safe Altitude (MSA)• True Air Speed (TAS)• Track Angle Error (TKE)• Track (TRK)• Vertical Speed Required (VSR)• Crosstrack Error (XTK)• Fuel Over Destination (FOD)• Fuel On Board (FOB)• Endurance (END)
G
PS CDI
The GPS CDI Box on the System Setup Page allows the pilot to define the range for the on-screen course deviation indicator (CDI). The range values represent full range deflection for the CDI to either side. The default setting is ‘AUTO’. Refer to the Flight Instruments sections for a discussion on CDI scaling.
If a lower CDI range setting is selected (i.e., 1.0 or 0.3 nm), the higher range settings are not selected during any phase of flight. For example, if 1.0 nm is selected, the G1000 uses this for en route and terminal phases and ramps down to 0.3 nm during an approach. Note that the Receiver Autonomous Integrity Monitoring (RAIM) protection limits follow the selected CDI range and corresponding flight phases.
The GPS CDI Box on the System Setup Page displays the following:
• Selected CDI range (auto, 2 nm, 1 nm, 0.3 nm)
• Current system CDI range (2 nm, 1 nm, 0.3 nm)
• ILS CDI capture mode setting (auto, manual)
To change the CDI range:
1) While on the System Setup Page, press the FMS Knob momentarily to activate the flashing cursor.
2) Turn the large FMS Knob to highlight the selected field in the GPS CDI Box.
3) Turn the small FMS Knob to display and scroll through the range list and press the ENT Key when the desired selection is highlighted.
38 Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 190-00494-02 Rev. B
System ystem Overview verview
SYSTEM
OVERVIEW
FLIGHT
AUDIO PANEL EICAS INSTRUMENTS
& CNS
FLIGHT
MANAGEMENT
HAZARD
ADDITIONAL AFCS AVOIDANCE
INDEX APPENDICES FEATURES
To change the ILS CDI capture setting:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
Cessna Citation Mustang G1000 Integrated Flight Dec(21)
