曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
OVERVIEW
FLIGHT
AUDIO PANEL EICAS INSTRUMENTS
& CNS
FLIGHT
MANAGEMENT
HAZARD
ADDITIONAL AFCS AVOIDANCE
INDEX APPENDICES FEATURES
When a descent leg is captured (i.e., vertical deviation becomes valid), Vertical Path Tracking becomes active and tracks the descent profile (Figure 7-15). An altitude capture mode (‘ALTS’ or ‘ALTV’) is armed as appropriate.
Figure 7-15 Vertical Path Tracking ModeVNV Target Altitude Capture ArmedVertical Path Tracking ActiveCommand Bars Indicate Descent toMaintain Required Vertical SpeedGPS is Selected NavigationSourceTerminalPhase ofFlightVNV Target AltitudeRequiredVerticalSpeed Indication(RVSI)Vertical Deviation Indicator (VDI)
If the altimeter barometric setting is adjusted while Vertical Path Tracking is active, the flight director increases/decreases the descent rate by up to 500 fpm to re-establish the aircraft on the descent path (without commanding a climb). Adjusting the altimeter barometric setting creates discontinuities in VNV vertical deviation, moving the descent path. For large adjustments, it may take several minutes for the aircraft to re-establish on the descent path. If the change is made while nearing a waypoint with a VNV Target Altitude, the aircraft may not re-establish on the descent path in time to meet the vertical constraint.
190-00494-02 Rev. B Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 381
Automatic utomatic utomatic Flight Control System ystem
SYSTEM
OVERVIEW
FLIGHT
INSTRUMENTS EICAS AUDIO PANEL
& CNS
FLIGHT
MANAGEMENT
HAZARD
AVOIDANCE AFCS ADDITIONAL
FEATURES APPENDICES INDEX
tomatic Reversion to Pitch Hold Mode
Several situations can occur while Vertical Path Tracking Mode is active which cause the flight director to revert to Pitch Hold Mode:
• Vertical deviation exceeds 200 feet during an overspeed condition.
• Vertical deviation experiences a discontinuity that both exceeds 200 feet in magnitude and results in the vertical deviation exceeding 200 feet in magnitude. Such discontinuities are usually caused by flight plan changes that affect the vertical profile.
• Vertical deviation becomes invalid (the Vertical Deviation Indicator is removed from the PFD).
• A display enters Reversionary Mode (this does not apply to an active direct-to with vertical constraint).
Unless VNV is disabled, Vertical Path Tracking Mode and the appropriate altitude capture mode become armed following the reversion to Pitch Hold Mode to allow for possible profile recapture.
N
on-Path Descents
Pitch Hold, Vertical Speed, and Flight Level Change modes can also be used to fly non-path descents while VNV flight control is selected. If the VS or FLC Key is pressed while Vertical Path Tracking Mode is selected, Vertical Path Tracking Mode reverts to armed along with the appropriate altitude capture mode to allow profile re-capture.
Figure 7-16 Flight Level Change VNV Non-Path Descent
To prevent immediate profile re-capture, the following must be satisfied:
• At least 10 seconds have passed since the non-path transition was initiated
• Vertical deviation from the profile has exceeded 250 feet, but is now less than 200 feet
Pressing the VNV Key twice re-arms Vertical Path Tracking for immediate profile re-capture.
382 Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 190-00494-02 Rev. B
Automatic utomatic utomatic Flight Control System ystem
SYSTEM
OVERVIEW
FLIGHT
AUDIO PANEL EICAS INSTRUMENTS
& CNS
FLIGHT
MANAGEMENT
HAZARD
ADDITIONAL AFCS AVOIDANCE
INDEX APPENDICES FEATURES
VNV Target Altitudeltitude Capture Mode (ALTV) Noteote: Armed VNV Target Altitude and Selected Altitude capture modes are mutually exclusive. However, Selected Altitude Capture Mode is armed implicitly (not annunciated) whenever VNV Target Altitude Capture Mode is armed.
VNV Target Altitude Capture is analogous to Selected Altitude Capture Mode and is armed automatically after the VNV Key is pressed and the next VNV Target Altitude is to be intercepted before the Selected Altitude. The annunciation ‘ALTV’ indicates that the VNV Target Altitude is to be captured. VNV Target Altitudes are shown in the active flight plan or direct-to (with vertical constraint), and can be entered manually or loaded from a database (see the Flight Management Section for details). At the same time as “TOD within 1 minute” is annunciated in the Navigation Status Box, the active VNV Target Altitude is displayed above the Vertical Speed Indicator (see Figure 7-14).
As the aircraft nears the VNV Target Altitude, the flight director automatically transitions to VNV Target Altitude Capture Mode with Altitude Hold Mode armed. This automatic transition is indicated by the green ‘ALTV’ annunciation flashing for up to 10 seconds and the appearance of the white ‘ALT’ annunciation. The VNV Target Altitude is shown as the Altitude Reference beside the ‘ALTV’ annunciation and remains displayed above the Vertical Speed Indicator. The Required Vertical Speed Indication (RVSI) is removed once VNV Target Altitude Capture Mode becomes active.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
Cessna Citation Mustang G1000 Integrated Flight Dec(135)
