曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
within the page group. Pressing the FMS Knob turns the selection cursor ON and OFF. When the cursor is ON, data may be entered in the applicable window by turning the small and large knobs. In this case, the large knob moves the cursor on the page, while the small knob selects individual characters for the highlighted cursor location.
2 Direct-to Key () – Allows the user to enter a destination waypoint and establish a direct course to the selected destination (the destination is either specified by the identifier, chosen from the active route, or taken from the map pointer position).
3 FPL Key – Displays the active Flight Plan Page for creating and editing the active flight plan, or for accessing stored flight plans.
4 MENU Key – Displays a context-sensitive list of options. This list allows the user to access additional features or make setting changes that relate to particular pages.
5 PROC Key – Gives access to IFR departure procedures (DPs), arrival procedures (STARs) and approach procedures (IAPs) for a flight plan. If a flight plan is used, available procedures for the departure and/or arrival airport are automatically suggested. Theses procedures can then be loaded into the active flight plan. If a flight plan is not used, both the desired airport and the desired procedure may be selected.
10 Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 190-00494-02 Rev. B
System ystem Overview verview
SYSTEM
OVERVIEW
FLIGHT
AUDIO PANEL EICAS INSTRUMENTS
& CNS
FLIGHT
MANAGEMENT
HAZARD
ADDITIONAL AFCS AVOIDANCE
INDEX APPENDICES FEATURES
6 Joystick – Changes the map range when rotated. Activates the map pointer when pressed.
7 Alphanumeric Keys – Allow the user to enter data quickly, without having to select individual characters with the FMS Knob.
8 Plus (+) Minus (-) Key – Toggles a (+) or (-) character.
9 Decimal Key – Enters a decimal point.
10 SEL Key – The center of this key activates the selected softkey, while the right and left arrows move the softkey selection box to the right and left, respectively.
11 ENT Key – Validates or confirms a menu selection or data entry.
12 CLR Key – Erases information, cancels entries, or removes page menus. Pressing and holding this key displays the Navigation Map Page automatically.
13 SPC Key – Adds a space character.
14 BKSP Key – Moves the cursor back one character space.
AFCS Controls NOTE: With the exception of the FD and SPD Keys, if a key is selected, its respective annunciator is illuminated.
12345678109171615141312111819Figure 1-4 AFCS Control Unit (GMC 710)
The GFC 700 AFCS is mainly controlled through the GMC 710 AFCS Control Unit. The AFCS Control Unit consists of the following controls:
1 HDG Key – Selects/deselects Heading Select Mode.
2 APR Key – Selects/deselects Approach Mode.
3 NAV Key – Selects/deselects Navigation Mode.
190-00494-02 Rev. B Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 11
System ystem Overview verview
SYSTEM
OVERVIEW
FLIGHT
INSTRUMENTS EICAS AUDIO PANEL
& CNS
FLIGHT
MANAGEMENT
HAZARD
AVOIDANCE AFCS ADDITIONAL
FEATURES APPENDICES INDEX
4 FD Key – Activates/deactivates the flight director in the default pitch and roll modes. If the autopilot is engaged, the FD Key is disabled.
5 XFR Key – Switches the autopilot between the pilot-side and the copilot-side flight directors. This selection also selects which air data computer is communicating with the active transponder and which PFD triggers the altitude alert. Upon power-up, the pilot-side FD is selected.
6 ALT Key – Selects/deselects Altitude Hold Mode.
7 VS Key – Selects/deselects Vertical Speed Mode.
8 FLC Key – Selects/deselects Flight Level Change Mode.
9 CRS2 Knob – Sets the copilot-selected course on the HSI of PFD2 when the VOR1, VOR2, or OBS/SUSP mode is selected. Pressing this knob centers the CDI on the currently selected VOR. The copilot-selected course provides course reference to the copilot-side flight director when operating in Navigation and Approach modes.
10 SPD Key – Switches the Flight Level Change mode reference speed between IAS and MACH number.
11 NOSE UP/DN Wheel – Controls the active mode reference for the Pitch, Vertical Speed, and Flight Level Change modes.
12 VNV Key – Selects/deselects Vertical Navigation mode.
13 ALT SEL Knob – Sets the selected altitude in the Selected Altitude Box. In addition to providing the standard G1000 altitude alerter function, selected altitude provides an altitude setting for the Altitude Capture/Hold mode of the AFCS.
14 YD Key – Engages/disengages the yaw damper.
15 AP Key – Engages/disengages the autopilot.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
Cessna Citation Mustang G1000 Integrated Flight Dec(10)
