曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
Yes No
(B) Please provide the following details with respect to the Landing Gears
Part No. When was
the Last
overhaul
done
When is the
next overhaul
due
Overhaul
interval in
hours or
cycles or
calendar
time
Nose Landing Gear
LH Main Landing gear
Tender No.DL/777-200ER/June 2007
10
RH Main Landing Gear
Nose Gear Wheel Part No. __________________
Main Gear Wheel Part No. __________________
Brake Part No. __________________
Nose wheel tire size _________________ Bias/Radial________________
Main gear wheel tire size _________________ Bias/Radial_________________
Brake cooling fan : Installed / Not Installed
( C) Please provide the following details with respect to the following Avionics
ATA
Ch
System/ LRU Hardware
Part No.
Software Part No. Vendor
22 AFS
22 FMGEC
22 MCDU
22 FCU
23 CIDS
23 SATCOM
23 ACARS
23 SELCAL
30 Ice Detection
System
31 ACMS- DMU
31 EIS
31 CWS
34 ADIRS
34 MMR
34 GPS
45 CMC
45 Air Borne Data
loader
D) Please provide the following details with respect to the (proposed)
installed engines & APU at delivery :
Engine position : # 1 # 2
Tender No.DL/777-200ER/June 2007
11
Engine S/N :
Engine TSN/CSN :
Engine TSO/CSO :
Engine TSLV/CSLV :
Reason for Last Shop Visit :
Brief Description of job done on
engine during last shop visit :
First Life Limiter
EGT Margin at Take Off
- In Test Cell
- On Wing
Engine Module Data
Please fill in the required data for all modules such as Fan, LPC, HPC, Combustor,
HPT, LPT, all gear boxes, all mainline bearings, engine mounts, etc. – separately for
all the installed engines – in the table given below.
Engine No. 1 S/N :
Description Serial No. Life Done
TSN/CSN TSO/CSO TSLV/CSLV
Brief Description of Job
Done on each module
Engine No. 2 S/N :
Description Serial No. Life Done
TSN/CSN TSO/CSO TSLV/CSLV
Brief Description of Job
Done on each module
Applicability and compliance status of the following SB’s and other salient
features of the proposed installed engines.
1) FAA/JAA –ADs should be Complied. Provide compliance status
2) LLP status.
3) Furnish list of modifications complied on engine and module.
Tender No.DL/777-200ER/June 2007
12
4) Copy of Last Boroscope inspection of complete engine including
compressor.
5) Last shop visit details of the engine with details like TSO/CSO of each
module.
6) ETOPS requirements status
APU Details
APU
APU Type
Sl. No.
TSN/CSN
TSLV/CSLV
Time/cycles since component refurbishment
Time/cycles since Hot Section refurbishment
Brief description of work carried out during
last shop visit along with copy of LLP list
(Can be given as an annexure)
Status of SBs / FAA/JAA AD status
E) In-flight & Passenger Amenities
1) Air – India uses standard ‘ATLAS’ equipment (sizes of major galley
equipment are given below). Please specify the type of Galley
Equipment being used on your aircraft.
EQUIPMENT OVERALL DIMENSION INTERNAL
DIMENSIONS
Meal/Bar Cart Full
(14 Racks)
Height (1008.38 mm) Width
(302.26 mm) Depth (805.18
mm
Height (850.5 mm)
Width (276 mm)
Depth (771 mm)
Meal/Bar Cart Half
(14 Racks)
Height (1008.38 mm) Width
(302.26 mm) Depth (404 mm)
Height (849 mm)
Width (276 mm)
Depth (382 mm)
Standard Unit
2 Drawers
Height (279 mm) Width (288
mm) Length (396 mm)
Oven Cage (8
Racks)
Height (414.2 mm) Internal
Width (215.5 mm)
Length (389 mm)
Loading Drawers Height (102 mm) Width (266.5
mm) Length (375 mm)
Tender No.DL/777-200ER/June 2007
13
Please specify the chilled galley locations?
How many refrigerator units are available in the aircraft?
What is the type of chilling units installed for chilling of meals/ bar carts and
chiller units for ovens?
How are the meal/bar carts and second meals chilled in the galleys?
Please submit detailed galley diagrams/drawings and Galley Loading
Plans of all galleys in the aircraft which is in use presently by the Airline
using the aircraft.
Please submit dimensions / sizes of all galley insert equipment (eg. Ovens /
Oven Cages, standard units, hot beverage flasks, hot cups, etc).
Please specify the galley capacity in the aircraft?
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
航空资料7(32)
