(4)
B00083 Solvent - Aliphatic Naphtha, TT-N-95
(5)
G00382 Pad - Abrasive, Aluminum Oxide, 240 Grit (Minimum)
(6)
G00382 Paper - Abrasive, Aluminmum Oxide, 240 Grit (Minimum)
(7)
G00378 Alodine 1000
(8)
B00352 Alodine 1200
(9)
B00352 Alodine 1200S
(10)
B00107 Sheet - Scothbrite
(11)
G00034 Cheesecloth - Clean and Lint Free
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-21-21
ALL ú ú B02 Page 703 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
C.
D.
E.
A
737-300/400/500MAINTENANCE MANUAL
(12)
C00259 Primer - BMS 10-11
(13)
C00584 Primer - BMS 10-79References
(1)
AMM 51-21-99/701, Decorative Exterior Paint System
(2)
AMM 51-21-41/701, Alodine CoatingPrepare the Surface with Pretreatment Procedure I (Before you apply the wash or epoxy primer system without Alodine treatment.)
S 117-039-B00
CAUTION: BE CAREFUL WHEN YOU CLEAN AROUND THE FASTENERS, SEAMS AND LAP
_______ JOINTS. THIS IS TO PREVENT DAMAGE TO THE FASTENERS, SEAMS AND LAP JOINTS.
(1) Prepare the alkaline cleaner.
(a) Mix 1 part by volume of alkaline cleaner with 3 parts by volume of water.
S 167-016-B00
(2)
Use abrasive pads and alkaline cleaner to make the surface rough.
S 177-026-B00
(3)
Flush the surface with water until you get a water break-free surface.
NOTE: A water break-free surface will have a continuous layer of
____
water for 30 seconds.
(a)
Make sure you flush all unwanted material from the joints and fasteners.
(b)
If you do not get a water break-free surface, rough the surface and flush it with water again.
S 167-017-B00
(4)
Let the surfaces, seams and the lap joints dry fully.
S 397-027-B00
(5)
Seal all openings that have leaks.
S 377-028-B00
(6)
Apply the primer on the surface (AMM 51-21-99/701).
Prepare the Surface with Pretreatment Procedure II: Alodine 1000, 1200
or 1200S (Before you apply the epoxy primer system)
S 167-018-B00
CAUTION:_______DO NOT USE SOLVENTS. SOLVENTS WILL CHANGE THE WATER BREAK-FREE PROPERTY OF THE TREATED SURFACE.
(1) Use scotchbrite sheets and clean water to make the surface rough.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-21-21
ALL ú ú B01 Page 704 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 167-034-B00
(2)
Use a cheesecloth that is moist with water to clean the surface.
S 167-035-B00
(3)
Clean the surface again to remove all remaining particles.
S 177-029-B00
(4)
Flush the surface with water until you get a water break-free surface.
NOTE: A water-break free surface will have a continuous layer of
____
water for 30 seconds.
(a)
Make sure you flush all unwanted material from the joints and fasteners.
(b)
If you do not get a water break-free surface, rough the surface and flush it with water again.
S 377-019-B00
WARNING: DO NOT GET ALODINE IN YOUR MOUTH OR EYES, ON YOUR SKIN OR
_______ CLOTHES. DO NOT BREATHE THE VAPOR, MIST OR DUST FROM THIS MATERIAL. DO NOT PERMIT THE CLOTHS USED TO APPLY OR REMOVE THE ALODINE SOLUTION TO DRY OUT. THEY ARE A FIRE HAZARD WHEN DRY. CLEAN THE CLOTHS FULLY WITH WATER. THIS MATERIAL IS POISONOUS AND FLAMMABLE AND CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(5)
Apply the Alodine 1000, 1200 or 1200S (AMM 51-21-41/701).
S 167-020-B00
(6)
Before you apply the primer, let the surfaces, seams and the lap joints fully dry.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 结构 STRUCTURES(18)
