曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
output power, ID code
3) Calibrate 5 Flight inspection
4) Troubleshoot 5 Carrier frequency deviation, depth
of modulation, lack of power,
harmonics ratio
6.3 Ground Based Systems - VDF/DDF/IDF
1. Use of the System 1) Explain the operational use of DF 2 Terminal and approach
procedures, emergency, back-up
2) Describe the user HMI 2 Indication on radar picture, DF
indicator
3) Theorize the principles of DF 5 Bearing, measuring method
(standard, Doppler,
interferometry)
4) Explain the advantages of DF 2 Simplicity, cost
5) Explain the disadvantages of DF 2 Sensitivity to interference
6) Describe the current situation 2 Density and types of DF in use in
your area, effective use of DF
Advance first edition (unedited) version – 30 August 2009
70
Topic Intermediate Objectives
The students should be able to:
Level Content
2. VDF/DDF 1) Draw and explain the block 2 Electronic cabinet, antennas,
Equipment diagram of a VDF/DDF equipment power supply, remote controls
Architecture and monitoring
2) Design a VDF/DDF equipment
according to operational
requirements
4 Coverage, accuracy
3. Receiver Sub
System
1) Design main signal parameters 4 Frequency band (UHF, VHF)
2) Perform typical measurements on 3 Frequency, channel spacing,
the receiver sensitivity, selectivity
4. Antenna Sub 1) Explain and describe antenna 2 Impedance, polar diagram,
System parameters for VDF/DDF polarization, types of antennas
2) Design protection areas 4 Obstacles, Annexes 10 and 14,
manuals
5. Monitoring and 1) Describe and explain which 2 Noise figure, stability of
Control Sub parameters are used for the measurement
System monitoring
2) Check the operational status of 3 BITE, system status e.g.
the monitor system watchdog
3) Troubleshoot wrong bearing
instructions
5 Re-adjust antenna systems
6. Implementation 1) Verify the impact of the
requirements on the choice of the
VDF/DDF location
3 Protection of receivers
2) Check the conformity of the
system to ITU
3 ITU regulation, ICAO Annex 10
3) Check the conformity to national
regulations
3 National regulations
7. Compliance with 1) Define the global performances 2 Accuracy, coverage, Annex 10
Standards recommendations
2) List VHF/UHF receiver procedures 1
3) Calibrate the system 5 Flight inspection
6.4 Ground Based Systems - VOR
1. Use of the System 1) Explain the operational use of 2 En route, terminal area,
VOR procedures
2) Theorize the principles of the 5 Bearing information, phase
CVOR measurements methods
3) Explain the advantages of VOR 2 Type of information (azimuth),
accuracy, integrity, suitable for a
network of fixed routes
4) Explain the disadvantages of VOR 2 Multipath, sensitivity to
interference, limited coverage, not
ideal for free routes, accuracy
depending on distance
5) Justify and theorize the DVOR 4/5 CVOR, DVOR, signal broadcast
versus the CVOR differences, bearing information
Advance first edition (unedited) version – 30 August 2009
71
Topic Intermediate Objectives
The students should be able to:
Level Content
6) Describe the current situation 2 Density of CVOR and DVOR in
use in your area
2. Ground Station 1) Draw and explain the block 2 Electronic cabinet, antenna
Architecture diagram of a CVOR ground system, power supply, remote
station controls and monitoring
2) Design a CVOR station according
to operational requirements
4 Coverage, identification code
3. Transmitter Sub 1) Analyze main signal parameters 4 Carrier frequency stability, output
System for a CVOR power, signals generated
2) Analyze main signal parameters
for a DVOR
4 Output power, signals generated
3) Perform the typical measurements 3 Power measurements, spectrum
on the signals by using standard measurements, modulation
equipment measurements
4. Antenna Sub 1) Explain and describe the generic 2 Patterns antennas, distribution
System radiated signals required for
CVOR
circuits, standard implementations
2) Explain and describe the generic 2 Patterns antennas, distribution
radiated signals required for
DVOR
circuits, standard implementations
3) Analyze the interface between 4 Standing Wave Ratio (SWR),
power stage and the antenna radiated power
4) Analyze the most typical signal
errors due to the antenna
4 Error expression components
5. Monitoring and
Control Sub
System
1) Describe and explain which
parameters are used for the
monitoring
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
Air Traffic Safety Electronics Personnel (ATSEP)(36)
