Loss of the A/THR Control on Engine 1
1. Possible Causes
_______________
- EIU-1 (1KS1)
- harness J3 between the EIU (1KS1) and the ECU (4000KS)
- wiring between the FCU (2CA) and the EIU (1KS1)
- FCU (2CA)
- FMGC (1CA1)
- ECU (4000KS)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 22-81-12-000-001 Removal of the FCU (2CA)
AMM 22-81-12-400-001 Installation of the FCU (2CA)
AMM 22-83-34-000-001 Removal of the FMGC (1CA1,1CA2)
AMM 22-83-34-400-001 Installation of the FMGC (1CA1,1CA2)
AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS)
AMM 73-21-60-400-001 Installation of the Electronic Control Unit
(ECU)(4000KS) AMM 73-25-34-000-040 Removal of the Engine Interface Unit (EIU) (1KS1,1KS2) AMM 73-25-34-400-040 Installation of the Engine Interface Unit (EIU) (1KS1,1KS2) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with
Engine non Motoring) ASM 73-25/06 ASM 73-25/10
3. Fault Confirmation
__________________
A. Test Do the operational test of the FADEC 1B on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
F 『 EEFF : ALL E ∞∞73-25-00∞∞∞∞∞∞∞∞∞∞Page A212
E E Aug 01/05 ERE
ECES 4. Fault Isolation
F 『
E C F M E
E E
E 56 E
E E
_______________
A. If the test gives the maintenance message FCU, EIU (ATN1), J3:
- do a check for open or short to ground at the harness J3 between the EIU (1KS1) and the ECU (4000KS) pins AB/5A, 5C to pins J3/22, 23 (Ref. ASM 73-25/06) and (Ref. ASM 73-25/10).
(1) If the fault continues:
- replace the EIU-1 (1KS1) (Ref. AMM TASK 73-25-34-000-040) and (Ref. AMM TASK 73-25-34-400-040).
(2) If the fault continues:
- do a check of the wiring between the FCU (2CA) and the EIU (1KS1) pins AA/DD, EE to pins AA/1J, 1K.
(a) If the wiring is not correct:
- repair the above wiring.
(b) If the wiring is correct:
- replace the FCU (2CA) (Ref. AMM TASK 22-81-12-000-001) and (Ref. AMM TASK 22-81-12-400-001).
(3) If the fault continues:
- replace the FMGC (1CA1) (Ref. AMM TASK 22-83-34-000-001) and (Ref. AMM TASK 22-83-34-400-001).
(4) If the fault continues:
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
B. Do the test given in Para. 3.A.
F 『 EEFF : ALL E ∞∞73-25-00∞∞∞∞∞∞∞∞∞∞Page A213
E E Aug 01/05 ERE
ECES
F 『
E C F M E
E E
E 56 E
E E
TASK 73-25-00-810-927
Loss of the A/THR Control on Engine 2
1. Possible Causes
_______________
- EIU-2 (1KS2)
- harness J3 between the EIU (1KS2) and the ECU (4000KS)
- wiring between the FCU (2CA) and the EIU (1KS2)
- FCU (2CA)
- FMGC (1CA2)
- ECU (4000KS)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 22-81-12-000-001 Removal of the FCU (2CA)
AMM 22-81-12-400-001 Installation of the FCU (2CA)
AMM 22-83-34-000-001 Removal of the FMGC (1CA1,1CA2)
AMM 22-83-34-400-001 Installation of the FMGC (1CA1,1CA2)
AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS)
AMM 73-21-60-400-001 Installation of the Electronic Control Unit
(ECU)(4000KS) AMM 73-25-34-000-040 Removal of the Engine Interface Unit (EIU) (1KS1,1KS2) AMM 73-25-34-400-040 Installation of the Engine Interface Unit (EIU) (1KS1,1KS2) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with
Engine non Motoring)
ASM 73-25/06
ASM 73-25/10
3. Fault Confirmation
__________________
A. Do the operational test of the FADEC 2B on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 发动机燃油和控制 2(71)
