A320 Trouble Shooting Manual 排故手册 指示和记录系统 3(102)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 (2WT1,2WT2,3WT1,3WT2,4WT1,4WT2) AMM 31-63-22-400-001 Installation of the Display Unit
 (2WT1,2WT2,3WT1,3WT2,4WT1,4WT2) AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3) AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3) ASM 31-61/02 ASM 31-68/01 ASM 31-68/02
 3. Fault Confirmation
__________________
 A. Job Set-up Do the EIS start procedure (CAPT ND only) (Ref. AMM TASK 31-60-00-860-001).
 B. Test
 Make sure that the CAPT ND stays off.

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞31-63-82∞∞∞∞∞∞∞∞∞∞Page 210
 201-299, 301-399, Aug 01/05 CES

 4. Fault Isolation
_______________

 A. If the CAPT ND stays off and if the EIS DMC selector switch (18WT) on the SWITCHING panel 8VU is at NORM:
 (1) Do a check for 115VAC at pin AA/104 of the CAPT ND (3WT1) (Ref. ASM 31-61/02).
 (a) If there is 115VAC:

 - replace the ND-CAPT (3WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).

 (b) If there is no 115VAC:

 - do a check for a ground signal at pin AA/102 of the CAPT ND (3WT1).
 1_ If there is no ground signal:
 - repair the wiring from CAPT ND (3WT1) pin AA/102 to the
 ground terminal.

 2 If there is a ground signal:
_

 - do a check of the wiring from CAPT ND (3WT1) pin AA/104 to the circuit breaker (12WT1).
 a If there is no continuity:
_ - repair the wiring.

 b If there is continuity:
_ - replace the C/B-EIS/ND/CAPT (12WT1).

 (2) If the fault continues:
 - do a check of the wiring from CAPT ND (3WT1) pins AA/49, 50, 51, 52 to CAPT ND potentiometer (8WT1) pins A/2, 4, 5, 6 (Ref. ASM 31-68/01).
 (a) If there is continuity:
 - replace the ND-CAPT (3WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
 1 If the fault continues:
_

 - replace the POT-ND, CAPT (8WT1) (Ref. IPC 316808).
 (b) If there is no continuity:
 - repair the wiring from CAPT ND (3WT1) pins AA/49, 50, 51, 52 to CAPT ND potentiometer (8WT1) pins A/2, 4, 5, 6.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞31-63-82∞∞∞∞∞∞∞∞∞∞Page 211
 201-299, 301-399, Aug 01/05 CES

 

 B. If the CAPT ND stays off and if the EIS DMC selector switch (18WT) on the SWITCHING panel 8VU is at CAPT/3:
 (1) Do a check for 28VDC at pin AA/93 on the CAPT ND (3WT1) (Ref. ASM 31-61/02).
 (a) If there is 28VDC:

 - replace the ND-CAPT (3WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).

 (b) If there is no 28VDC:

 - do a check for a ground signal at pin AA/106 of the CAPT ND (3WT1).
 1 If there is no ground signal:
_

 - repair the wiring from CAPT ND (3WT1) pin AA/106 to the ground terminal.
 2 If there is a ground signal:
_

 - do a check of the wiring from CAPT ND (3WT1) pin AA/93 to the circuit breaker (23WT1).
 a If there is no continuity:
_ - repair the wiring.

 b If there is continuity:
_ - replace the C/B-EIS/ND/CAPT/SWTG (23WT1)

 (2) If the fault continues:
 - do a check for 115VAC at pin AC/2 of the DMC3 (1WT3) (Ref. ASM 31-61/02).
 (a) If there is 115VAC:

 - replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).

 (b) If there is no 115VAC:

 - do a check for a ground signal at pin AC/7 of the DMC3 (1WT3).
 1 If there is no ground signal:
_

 - repair the wiring from DMC3 (1WT3) pin AC/7 to the ground terminal.
 2 If there is a ground signal:
_ - replace the RELAY-BUS1 TO ESS BUS SWTG, DMC3 (26WT).

 a If the fault continues:
_

 - replace the C/B-EIS/DMC3/STBY/SPLY (14WT1) . If the fault continues:
 * do a check of the wiring from the DMC3 BUS1 TO ESS BUS SWTG relay (26WT): . pin A2 to DMC3 (1WT3) pin AC/2
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞31-63-82∞∞∞∞∞∞∞∞∞∞Page 212
 201-299, 301-399, Aug 01/05 CES . pin A1 t the EIS/DMC3/STBY/SPLY circuit breaker (14WT1) . pin X2 to the BUS 1XP CTL relay (20XN1)

 
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 指示和记录系统 3(102)