__________________
A. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU HYDRAULIC/LOW/LVL/IND 1832GQ N32 121VU HYDRAULIC/HYD/QTY/IND 1831GQ P35 121VU HYDRAULIC/G HYD/PUMP ENG1/MONG 1702GK R34
B. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only) (Ref. AMM TASK 31-60-00-860-001).
(3) On the ECAM control panel on the center pedestal, push the HYD pushbutton switch. Make sure that the HYD page is shown on the system display of the ECAM.
(4) Look for fault indications on the upper ECAM DU, the lower ECAM DU and panel 40VU.
4. Fault Isolation
_______________
A. If the Fault Confirmation gives:
- The content indication shows high fluid level on the lower ECAM DU:
- Do a visual check of the fluid quantity shown on the mechanical indicator (1834GQ) on the ground service panel of the Green hydraulic system.
- Do a visual check of the fluid quantity shown on the fluid content indicator of the Green reservoir.
- Do a check of the pressure of the Green system accumulator (Ref. AMM TASK 29-10-00-200-003).
- Do a check of the pressure of the Green hydraulic reservoir (Ref. AMM TASK 29-10-00-200-002).
(1) If the three hydraulic fluid quantity indicators show different quantities and the pressures of the accumulator and the reservoir are correct:
(a) Do the troubleshooting of the quantity indication system (Ref. TASK 29-11-00-810-803).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞29-11-00∞∞∞∞∞∞∞∞∞∞Page 238
Nov 01/04R
CES
(2) If the three hydraulic fluid quantity indicators show high level and the pressures of the accumulator and the reservoir are correct:
(a) Drain the hydraulic fluid until you have the correct fluid quantity in the reservoir (Ref. AMM TASK 29-10-00-680-001).
(b) Pressurize the reservoir of the Green hydraulic system (Ref. AMM TASK 29-14-00-614-002).
(3) If the three hydraulic fluid quantity indicators show high level, the pressure of the accumulator is correct, but the reservoir pressure is less than the permitted tolerance:
(a) Do a check for external gas leaks on the reservoir and repair the defective components as necessary (Ref. AMM TASK 29-10-00-200-002).
(b) If you find no external gas leaks, or the fault continues: 1 Do the troubleshooting for the loss of the reservoir
_ pressurization (Ref. TASK 29-11-00-810-801).
2 Drain the hydraulic fluid until you have the correct fluid
_ quantity in the reservoir (Ref. AMM TASK 29-10-00-680-001).
3 Pressurize the reservoir of the Green hydraulic system (Ref.
_
AMM TASK 29-14-00-614-002).
4 After 5 minutes, read the gage of the fluid quantity indicator
_
of the Green reservoir.
a If the difference of the fluid quantity is not more than 2
_
liter:
- No further actions are necessary. b If the difference of the fluid quantity is more than 2
_
liter:
- Do the bleeding procedures of the Green hydraulic system (Ref. AMM TASK 29-00-00-870-001), (Ref. AMM TASK 29-00-00-870-002) and (Ref. AMM TASK 29-00-00-870-003).
(c) If the fault continues: 1 Do the troubleshooting procedure (Ref. TASK 29-11-00-810-813).
_
(4) If the three hydraulic fluid quantity indicators show high level, the pressure of the reservoir is correct, but the accumulator pressure is less than the permitted tolerance:
(a) Do the troubleshooting procedure (Ref. TASK 29-11-00-810-813).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞29-11-00∞∞∞∞∞∞∞∞∞∞Page 239
Nov 01/04R CES
B. Do the procedure as given in Para. 3. B. to make sure that the operation of the hydraulic quantity indication is correct.
5. Close-up
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 液压(30)
