曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
free yourself to concentrate on the approach.
In setting up for the expected approach procedure
when using an RNAV, GPS, or FMS system, it is
important to understand how multiple approaches to
Figure 4-19. Arrival Clearance.
"Piper 52 Sierra, cleared to Logan
International via the GARDNER
TWO ARRIVAL, Albany Transition,
maintain 9,000."
You need to change VOR frequencies at the mileage
breakdown point. Follow the 110° radial from Albany
VOR to 23 DME, then change to the 294° radial off
of the Gardner VOR.
The textual description indicates
different altitude and airspeed
restrictions for turbojet and nonturbojet aircraft.
At this point, you join the
STAR on the 111° radial
from Gardner VOR.
At REVER Intersection, you fly
inbound to the Boston VOR on
the 030° radial.
This note indicates that you can expect radar
vectors to the final approach course. Have a
plan of action in the event of a communication
failure.
inbou
03
REVE
nd
on. (Naming conventions for approaches are covered in
more depth in the next chapter.) [Figure 4-20]
ALTITUDE
Upon your arrival in the terminal area, ATC either
clears you to a specific altitude, or they give you a
"descend via" clearance that instructs you to follow
the altitudes published on the STAR. [Figure 4-21 ]
You are not authorized to leave your last assigned altitude unless specifically cleared to do so. If ATC
amends the altitude or route to one that is different
from the published procedure, the rest of the charted
Figure 4-20. Here are two RNAV (GPS) approaches to Runway 15R at Baltimore. A controller issuing a clearance for one of these
approaches would speak the identifying letter—for example, “…c ea ed o r t heRNAV GPS Yankeeapp oach , Runway15R…”
"Cessna 20350, cleared via the JANESVILLE
FOUR ARRIVAL."
The controller is only giving you a routing clearance
and will specify any altitudes and airspeeds to fly.
"Cessna 20350, descend via the
JANESVILLE FOUR ARRIVAL."
Descent is at your discretion; however,
you must adhere to the minimum crossing altitudes and airspeed restrictions
printed on the chart.
Figure 4-21.Assigned Altitudes.
4-21
4-22
descent procedure is canceled. ATC will assign you any
further route, altitude, or airspeed clearances, as necessary. Notice the JANESVILLE FOUR ARRIVAL
depicts only one published arrival route, with no named
transition routes leading to the basic STAR procedure
beginning at the Janesville VOR/DME. Vertical navigation planning information is included for turbojet and
turboprop airplanes at the bottom of the chart.
Additionally, note that there are several ways to identify
the BRIBE reporting point using alternate formation
radials, some of which are from off-chart NAVAIDs.
ATC may issue a descent clearance that includes a crossing altitude restriction. In the PENNS ONE ARRIVAL,
the ATC clearance authorizes you to descend at your discretion, as long as you cross the PENNS Intersection at
6,000 feet MSL. [Figure 4-22]
In the United States, Canada, and many other countries,
the common altitude for changing to the standard
altimeter setting of 29.92 inches of mercury (or 1013.2
hectopascals or millibars) when climbing to the high
altitude structure is 18,000 feet. When descending from
high altitude, the altimeter should be changed to the
local altimeter setting when passing through FL 180,
although in most countries throughout the world the
change to or from the standard altimeter setting is not
done at the same altitude for each instance.
For example, the flight level where you change your
altimeter setting to the local altimeter setting is specified
by ATC each time you arrive at a specific airport. This
information is shown on STAR charts outside the U.S.
with the words: TRANS LEVEL: BY ATC. When
departing from that same airport (also depicted typically
on the STAR chart), the altimeter should be set to the
standard setting when passing through 5,000 feet, as an
example. This means that altimeter readings when flying above 5,000 feet will actually be flight levels, not
feet. This is common for Europe, but very different for
pilots experienced with flying in the United States and
Canada.
RNAV STARS OR STAR TRANSITIONS
STARs designated RNAV serve the same purpose as
conventional STARs, but are only used by aircraft
equipped with FMS or GPS. An RNAV STAR or STAR
transition typically includes flyby waypoints, with flyover waypoints used only when operationally
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
Instrument Procedures Handbook (IPH)仪表程序手册上(101)
