钻石40飞机维护手册 DA 40 SERIES AMM 5(81)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

(3)  Connect the 2 electrical in-line connectors for the power lever. 
(4)  Check for correct potentiometer signal with ECU Operator software (Overview page). S Left and Right potentiometer signals should not differ by more than 20 units. S Power Setting must be at 0 % with the power lever at IDLE and 99.9 % with the power lever at MAX.  Refer to Section 72-01. 
(5)  Put the power lever and the bottom cover plate in position in the center console. 
(6)  Install the 2 screws that attach the cover plate at the rear. 
(7)  Install the top cover plate to the center console. S Install the 2 screws that hold the top cover plate on top of the bottom cover plate. 
(8)  Install the lever for the emergency fuel valve: S Put the lever in position on the shaft. S Install the screw. 
(9)  Do a test for correct operation of the emergency fuel valve lever: S Move the lever from OFF to NORMAL to EMERG. TRANSFER.  Make sure that the safety lock operates correctly. 
(10)  Do a ground run-up.  Refer to Section 71-01. 

%

Doc # 6.02.01 Page 203
Rev. 4 09 Jan 2003

76-01-00
AMM

% 
%  Ambient Press.  Manifold Press. 
%  Hose, ECU A  Hose, ECU A 

% % % % % % Figure 3: ECU Installation %
76-01-00
Engine Controls
AMM

% 3. Remove/Install the ECU
%
%

%

%
%

%

%
%
%

%
%
%

%
%

% A. Remove the ECU

Detail Steps/Work Items  Key Items/References 
(1)  Make sure that the engine is safe: S Set the ELECTRIC MASTER key switch to OFF. S Set the ENGINE MASTER switch to OFF. S Set the power lever to IDLE. 
(2)  Remove the left pilot’s seat.  Refer to Section 25-10. 
(3)  Release the 2 electrical connectors from the ECU.  Refer to Figure 3. 
(4)  Release the 4 hose connections from the ECU. 
(5)  Release the 4 bolts and washers that hold the ECU to the mounting brackets. 
(6)  Remove the ECU from the airplane. 

%

Doc # 6.02.01 Page 205
Rev. 4 09 Jan 2003

76-01-00
AMM

% CAUTION: YOU MUST CONTACT THE ENGINE MANUFACTURER BEFORE YOU % INSTALL A NEW ECU. % %
%

%
%

%

%
%
%

%
%
%

%
%
%

% B. Install the ECU

Detail Steps/Work Items  Key Items/References 
(1)  Make sure that the engine is safe: S Set the ELECTRIC MASTER key switch to OFF. S Set the ENGINE MASTER switch to OFF. S Set the power lever to IDLE. 
(2)  Put the ECU in position below the pilot’s seat.  Refer to Figure 3. 
(3)  Install the 4 bolts and washers that hold the ECU to the mounting brackets. 
(4)  Connect the 4 hoses to the ECU. 
(5)  Connect the 2 electrical connectors from the ECU.  Make sure that the bayonet lockings are engaged. 
(6)  Install the pilot’s seat.  Refer to Section 25-10. 
(7)  Do a ground run-up.  Refer to Section 71-01. 

%
%

Page 206 Doc # 6.02.01 09 Jan 2003 Rev. 4
76-01-00
Engine Controls
AMM

% 4. Remove/Install the Engine Control System Harness
% A. Remove the Engine Control System Harness % %
% % % %
% %
%
%
%
%
%

%
%
%

%

%
%
%
%
%
%

DA 40 Series

Detail Steps/Work Items  Key Items/References 
WARNING: MAKE THE ENGINE IS SAFE BEFORE YOU DO ANY WORK ON HARNESS. IF THE ENGINE STARTS THE PROPELLER CAN CAUSE INJURY OR DEATH. 
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：钻石40飞机维护手册 DA 40 SERIES AMM 5(81)