曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
(b) inspect the spreader, spreader gate and controls;
(c) inspect the spray pump fan, fan mount, fan brake, spray pump lines, booms
and boom supports;
(d) inspect the emergency dump doors and dump controls.
(11) Take the following additional action if the aircraft is a seaplane:
(a) inspect the external covering and internal structure of the floats or hull;
(b) drain the bilge compartments, refit and re-lock the drain plugs;
(c) inspect the float attachment struts, bracing wires and attachment fittings;
(d) inspect the water rudders, water rudder attachments and water rudder
controls, operate and check them for full and free movement in the correct
sense and for correct locking ;
Civil Aviation Regulations 1988 Scheds — 15
Amended CAR – 2nd Ed Legal Services Group
August 2003 Civil Aviation Safety Authority
(e) inspect the protective treatment and finish.
Section 2—The Engine
(1) Check the external and internal required placards.
NOTE: Reference should be made to the aircraft flight manual and airworthiness
directives for the required placards.
(2) Take the following action in relation to the cowls:
(a) remove, clean and inspect the cowls, cowl flaps and fastenings.
(3) Inspect, and record the compression of, each cylinder.
(4) Take the following action in relation to the engine oil system:
(a) drain the sump or tank and refit the plug and lockwire;
(b) drain the oil cooler and refit and secure the hose;
(c) either:
(i) remove, inspect, clean and refit the pressure filter and lockwire; or
(ii) remove, open and inspect the cartridge full flow filter and fit a new
cartridge and lockwire;
(d) inspect the oil cooler, oil temperature control valves, oil tank and attachment
fittings;
(e) inspect all oil lines, fittings, breather pipe and the oil cooler shutter;
(f) refill the sump or tank with the recommended grade and quantity of oil.
(5) Take the following action in relation to the ignition system:
(a) remove the spark plugs, clean and inspect them, check the spark plug
electrode gap, test the spark plugs and renew them if required;
(b) inspect the spark plug high tension leads and ceramics;
(c) inspect the magneto housing;
(d) inspect the breaker compartment and cam follower;
(e) inspect the breaker points for serviceability and check the breaker points
gap, magneto engine timing and synchronisation;
(f) inspect the switch and earth leads;
(g) refit and torque the spark plugs;
(h) refit the spark plug high tension leads.
(6) Take the following action in relation to the fuel system:
(a) place the fuel selector in the off position;
(b) remove, inspect, clean and refit the fuel strainers and screens and lockwire;
(c) drain and flush the carburettor fuel bowl and refit the plug and lockwire;
(d) inspect the carburettor or fuel injection components;
(e) inspect the throttle and mixture shafts;
(f) inspect all fuel lines and fittings;
(g) move the fuel selector from the off position;
(h) inspect the auxiliary fuel pump for operation;
(j) pressurise and purge the fuel system and inspect it for leaks.
(7) Take the following action in relation to the induction system:
(a) remove the air filters, clean them, inspect them and refit or renew them;
(b) inspect the hot and alternate air systems for the integrity of seals and for
serviceability of valves, shafts, bearings, magnets and hinges;
(c) inspect the induction manifold and hoses.
(8) Take the following action in relation to the exhaust system:
(a) inspect the exhaust system;
(b) remove the muffler shroud, inspect the muffler and refit the shroud;
Scheds — 16 Civil Aviation Regulations 1988
Legal Services Group Amended CAR – 2nd Ed
Civil Aviation Safety Authority August 2003
(c) inspect the muffler internally for security of baffle cones;
(d) inspect the cabin heat flexible hoses.
(9) Take the following action in relation to the engine cylinders and baffles:
(a) inspect the cylinder assemblies;
(b) inspect the cylinder base to the crankcase area;
(c) inspect the rocker covers;
(d) inspect the push rod housing seals.
(10) Take the following action in relation to the crankcase, accessory housing and
firewall:
(a) inspect the engine for evidence of oil leakage;
(b) inspect the accessories and drive belts;
(c) inspect the engine mounts and engine mountbolts;
(d) inspect the engine mount frame;
(e) inspect the firewall, including seals and sealant.
(11) Inspect the following controls for full and free movement in the correct sense:
(a) throttle, mixture and propeller;
(b) alternate air and carburettor heat;
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
澳大利亚Civil_Aviation_Regulations下(79)
