钻石40飞机维护手册 DA 40 SERIES AMM 3(83)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

(8)  Measure the end play in the hub assembly.  There should be 0.025 to 0.125 mm (0.001 to 0.005 in) of end play when correctly adjusted. 
(9)  Lower the airplane with the jacks.  Refer to Section 07-10. 
(10)  Install the wheel fairing: S Install 4 screws on the inner side. S Install the outer bolt. S Install the brake cover.  Only if the optional strut fairing (O.M 40-106) is installed. 

Page 202 Doc # 6.02.01 09 Jan 2003 Rev. 4
32-40-00
Landing Gear
AMM

3. Remove/Install the Nose Wheel
A. Equipment
Item  Quantity  Reference 
Padded trestle.  1  Commercial. 
Weight and strap.  1  Commercial. 

B. Remove the Nose Wheel
Detail Steps/Work Items  Key Items/References 
(1)  Remove the wheel fairing: S Remove 6 screws attaching the left half of the fairing to the right half. S Remove the 3 left and 3 right attaching screws. S Remove the fairing. 
(2)  Use weights to hold the rear fuselage down with the nose wheel clear of the ground.  Use a strap around the rear fuselage. 
(3)  Put a padded trestle under the fuselage just aft of the nose gear mounting. 
(4)  Remove the axle bolt: S Remove the cotter pin from the axle nut. S Remove the axle nut and washer. S Remove the axle bolt and washer. 
(5)  Remove the wheel from the fork. 

Doc # 6.02.01 Page 203
Rev. 4 09 Jan 2003

32-40-00
AMM

C. Install the Nose Wheel
DA 40 Series

Detail Steps/Work Items  Key Items/References 
(1)  Put the wheel in position in the fork. 
(2)  Install the axle bolt: S Install the washer onto the axle bolt. S Push the axle bolt into position through the axle. S Install a second washer onto the axle bolt. S Install the axle nut hand tight only! S Slowly rotate the wheel while tightening the axle nut, hand tight only! S Turn the axle nut counter-clockwise until the next cotter pin hole aligns with the axle nut. S Install the cotter pin.  Put Mastinox 6856K corrosion inhibitor or LPS-3 on the shank of the bolt. Clean corrosion inhibitor from the threads. To settle the tapered wheel bearing. 
(3)  Turn the nose wheel. Make sure that the valve cap does not touch the fork.  Clearance 2 mm (0.08 in) minimum. 
(4)  Remove the trestle from the front fuselage. 
(5)  Lower the nose wheel to the ground.  Remove the weights from the rear fuselage. 
(6)  Install the wheel fairing: S Put the 2 halves in position. S Install the 3 LH and 3 RH mounting screws. S Install the 6 screws which hold the fairing halves together. 

Page 204 Doc # 6.02.01 09 Jan 2003 Rev. 4
32-40-00
Landing Gear
AMM

4. Remove/Install a Brake Master Cylinder
A. Remove a Brake Master Cylinder
Detail Steps/Work Items  Key Items/References 
WARNING: DO NOT GET BRAKE FLUID ON YOU. BRAKE FLUID CAN CAUSE DISEASE. CAUTION: CLEAN UP SPILT BRAKE FLUID IMMEDIATELY. BRAKE FLUID CAN DAMAGE PAINT AND OTHER MATERIAL. 
(1)  Disconnect the brake pipe(s) from the brake master cylinder.  Catch the brake fluid. Put caps on all connections. Refer to Figure 3. 
(2)  Remove the top pivot pin. S Remove the cotter pin. S Remove the washer. S Remove the pivot pin. 
(3)  Release the bottom pivot pin. S Remove the cotter pin. S Remove the washer. S Move the master cylinder sideways off the pivot pin. 
(4)  Lift the master cylinder from the rudder pedal assembly. 

Doc # 6.02.01 Page 205
Rev. 4 09 Jan 2003

32-40-00
AMM

B. Install a Brake Master Cylinder
DA 40 Series

Detail Steps/Work Items  Key Items/References 
WARNING: DO NOT GET BRAKE FLUID ON YOU. BRAKE FLUID CAN CAUSE DISEASE. CAUTION: CLEAN UP SPILT BRAKE FLUID IMMEDIATELY. BRAKE FLUID CAN DAMAGE PAINT AND OTHER MATERIAL. 
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：钻石40飞机维护手册 DA 40 SERIES AMM 3(83)