• 热门标签

当前位置: 主页 > 航空资料 > 飞行资料 >

时间:2011-04-23 09:57来源:蓝天飞行翻译 作者:航空
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

3.16.2.1 Nav Select Screen. The primary control screen is NAV SELECT, accessed by pressing NAV .xed function key (Figure 3-25). Displays on the screen and ac-
tive soft keys for TACAN are as follows:
CONTROL/  FUNCTION 
INDICATOR 
NAV SELECT  Title of screen. 
TCN  Selects, and then toggles between 
TACAN channel or preset for edit. 
SETTINGS  Accesses RADIO -NAV settings 
page. 

3.16.2.2 Radio Nav Screen. Use Radio Nav screen to change modes of operation. This screen is accessed by

TM 1-1520-253-10

SA

pressing SETTINGS soft key on NAV SELECT screen. 3.16.3 Operation. The function of each control is as follows:
CONTROL/ INDICATOR  FUNCTION 
RADIO-NAV  Title of screen. 
BRG:  Displays TACAN selected station.  bearing  to  the 
RNG:  Displays TACAN slant range to the selected station. 
GS:  Displays TACAN computed groundspeed to the selected station. 
TTG:  Displays TACAN computed time to the selected station at the calculated groundspeed. 
AA/AGs  Toggles between air-to-air and air-to-ground mode. Selected mode is displayed in inverse video. 
TR/RCVs  Toggles between transmit/receive and receive only mode. Selected mode is displayed in inverse video. 
RTNg  Returns screen.  to  previously  selected 

3.16.2.3 TACAN Preset Screen. Use TACAN preset screen to change channel and mode settings of a preset. See Figure 3-25 for ways to access this screen. Displays on the screen and active soft keys are as follows:
CONTROL/ FUNCTION INDICATOR
TACAN PRESET Title of screen.
gPRESET  Change preset number.
gNAME  Change name of preset.
gCHANNEL  Change channel number.
A/A -A/Gs  Toggles between air to air and air to ground mode of operation.
TR/RCVs  Toggles between transmit/receive and receive only or receive only mode.
3.16.3.1 Test Procedure.
1.  
VTAC switch on instrument panel -TACAN.

2.
HSI CRS control (pilot and copilot) -Set 180° in course display.

3.
Access  NAV TESTS page by pressingTST .xed function key, then NAV soft key. To start test, TACAN soft key -Press, until TACAN is displayed in inverse video.

4.
All indications below TACAN should read P.

5.
Indications on the HSI shall be as follows:


a.  Distance indicator shall read between
399.5 and 000.5 nmi.
b.
No. 2 bearing pointer shall read between 177° and 183°.

c.  
Course deviation bar shall be centered within 1/2 dot, and To/From indicator shall indicate TO.

d.
TACAN indications on the HSI will be re-moved unless there is a station that the set is tuned to nearby.


3.16.3.2 Normal Operation Receive Mode.
1.
Choose channel, or preset on NAV SELECT screen.

2.
On  RADIO-NAV screen, AA/AG and TR/RCV soft keys -Press, until AG and RCV is in inverse video.

3.
Wait .ve seconds for signal acquisition and lock on.

4.
On CSC panel, NAV B monitor control -Press.

5.
Check  for correct station identi.er in ear-phones.

6.
Navigation information will consist of bearing information only displayed on the HSI.

 

3.16.3.3 Normal Operation Transmit/Receive Mode.
1. Choose channel, or preset on NAV SELECT screen.


TACAN is a transponder that emits ra-diation. Make sure no personnel are within 3 feet of either TACAN antenna when TACAN is used in Transmit/Receive mode.
2.
On  RADIO-NAV screen, AA/AG and TR/RCV soft keys -Press, until AG and TR is in inverse video.

3.
Wait .ve seconds for signal acquisition and lock on.
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:UH-60Q 直升机技术手册 直升机操作手册 1(98)