S 704-041
(11)
Do a test of the latch along the full length of the latch bar.
NOTE: The door must open when force is applied at a location on
____
the face of the latch bar.
TASK 25-23-01-904-042
5. Standard Spacer Panel Removal/Installation (Fig. 401)
__________________________________________
A. Equipment
(1) Latch Release Rod - Make from 0.125-inch
diameter by 6-inch long rod
B. Access
(1) Location Zone
200 Upper Half of Fuselage
C. Procedure - Remove the Spacer Panel
S 024-043
(1) To lower the PSU on the two sides of the spacer panel, do the steps that follow:
(a)
Put the latch release rod in the latch release access holes (2 locations) to release the latches.
(b)
Release the lanyard to lower the PSU.
S 024-096
(2)
Loosen the wing nuts on the inboard side while you hold the spacer panel.
S 024-097
(3)
Lower the spacer panel down. Remove the retaining springs from the air conditioning extrusion.
(4)
Remove the spacer panel.
S 024-046
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
25-23-01
ALL ú ú 04 Page 409 ú May 28/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
D. Procedure - Install the Spacer Panel
S 864-047
(1)
Put the outboard edge of the spacer panel on the air conditioning extrusion.
S 424-098
(2)
Install the retaining springs to the index holes in the air conditioning extrusion.
S 864-049
(3)
Apply hand pressure in the outboard direction and lift the spacer panel up.
S 424-099
(4)
Tighten the wing nuts on the inboard side.
S 864-050
(5)
Lift the PSU up until the latches are engaged.
TASK 25-23-01-904-051
6. PSU and NSFSB Sign Spacer Panel Removal/Installation (Fig. 401)____________________________________________________
A. Equipment
(1) Latch Release Rod - Make from 0.125-inch
diameter by 6-inch long rod
B. Access
(1) Location Zone
200 Upper Half of Fuselage
C. Procedure - Remove the Spacer Panel
S 864-007
(1) Open this circuit breaker on the overhead circuit breaker panel, P11, and attach a DO-NOT-CLOSE tag:
(a) 11P9, PASS SIGN CONT
S 024-052
(2)
To lower the PSU on the two sides of the spacer panel, do the steps that follow:
(a)
Put the latch release rod in the latch release access holes (2 locations) to release the latches.
(b)
Release the lanyard to lower the PSU.
(3)
Disconnect the electrical connector.
S 024-101
(4)
Loosen the wing nuts on the inboard side while you hold the spacer panel.
S 024-100
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
25-23-01
ALL ú ú 01 Page 410 ú May 28/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
S 024-102
(5)
Hold the spacer panel and push the plunger on the outboard clamps to release the outboard clamps from the air conditioning extrusion.
S 024-056
(6)
Remove the spacer panel.
D. Procedure - Install the Spacer Panel
S 864-057
(1)
Put the outboard edge of the spacer panel on the air conditioning extrusion.
S 424-103
(2)
Push the plungers and attach the outboard clamps to the index holes in the air conditioning extrusion.
S 424-104
(3)
Tighten the wing nuts on the inboard side.
S 864-059
(4)
Lift the spacer panel up until the latches are engaged.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：757 AMM 飞机维护手册 EQUIPMENT/FURNISHINGS 1(63)
