- repair the above wiring.
(2) If the wiring is correct:
- with the cable disconnected from the EVMU (2EV), do a resistance check of the EVMU between: pins 7C and 8D (40 to 80 Ohms).
(a) If the resistance values are in the specified limits:
- replace the EVMU (2EV), (Ref. AMM TASK 77-32-34-000-042) and (Ref. AMM TASK 77-32-34-400-042).
F 『 EEFF : ALL E ∞∞77-30-00∞∞∞∞∞∞∞∞∞∞Page 210
E E Aug 01/04 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
(b) If the resistance values are out of the specified limits: R - with the connector CC disconnected from the N2 speed sensor, do R a resistance check of the sensor between:
. pins 1 and 2 (40 to 80 Ohms) . pins 1 and 3 (> 10 Megohms) . pin 1 and the ground (> 10 Megohms)
1 If the resistance values are out of the specified limits:
_
- replace the SENSOR-N2 ROTATIONAL SPD (4001EV), (Ref. AMM TASK 77-11-20-000-002) and (Ref. AMM TASK 77-11-20-400-002).
2 If the resistance values are in the specified limits:
_
- replace the harness between the EVMU and the N2 speed sensor (Ref. ASM 77-32/02).
B. Do the vibration check to get the vibration data (Ref. AMM TASK 71-00-00-710-009).
F 『 EEFF : ALL E ∞∞77-30-00∞∞∞∞∞∞∞∞∞∞Page 211
E E Aug 01/04 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
TASK 77-30-00-810-808
Loss of the N2 Vibration Indication on Engine 2
1. Possible Causes
_______________
- EVMU (2EV)
- wiring from the EVMU (2EV) to the N2 speed sensor (4001EV)
- SENSOR-N2 ROTATIONAL SPD (4001EV)
- harness between the EVMU and the N2 speed sensor
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 71-00-00-710-009 Vibration Check
AMM 77-11-20-000-002 Removal of the N2 Speed Sensor (4001EV).
AMM 77-11-20-400-002 Installation of the N2 Speed Sensor (4001EV).
AMM 77-32-34-000-042 Removal of the Engine Vibration Monitoring Unit
(EVMU) AMM 77-32-34-400-042 Installation of the Engine Vibration Monitoring Unit (EVMU) ASM 77-32/02
3. Fault Confirmation
__________________
A. Test
Not applicable, you cannot confirm this fault on the ground.
4. Fault Isolation
_______________
A. If the Post Flight Report gives the maintenance message ENG2 N2 SPEED
SENSOR:
R - do a check for open or short to ground of the wiring from the EVMU
R (2EV) to the N2 speed sensor (4001EV) pins AB/8D, 7C to pins CC/1, 2
(Ref. ASM 77-32/02).
(1) If the wiring is not correct:
- repair the above wiring.
(2) If the wiring is correct:
- with the cable disconnected from the EVMU (2EV), do a resistance check of the EVMU between: pins 7C and 8D (40 to 80 Ohms).
(a) If the resistance values are in the specified limits:
- replace the EVMU (2EV), (Ref. AMM TASK 77-32-34-000-042) and (Ref. AMM TASK 77-32-34-400-042).
F 『 EEFF : ALL E ∞∞77-30-00∞∞∞∞∞∞∞∞∞∞Page 212
E E Aug 01/04 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
(b) If the resistance values are out of the specified limits: R - with the connector CC disconnected from the N2 speed sensor, do R a resistance check of the sensor between:
. pins 1 and 2 (40 to 80 Ohms) . pins 1 and 3 (> 10 Megohms) . pin 1 and the ground (> 10 Megohms)
1 If the resistance values are out of the specified limits:
_
- replace the SENSOR-N2 ROTATIONAL SPD (4001EV) (Ref. AMM TASK 77-11-20-000-002) and (Ref. AMM TASK 77-11-20-400-002).
2 If the resistance values are in the specified limits:
_
- replace the harness between the EVMU and the N2 speed sensor (Ref. ASM 77-32/02).
B. Do the vibration check to get the vibration data (Ref. AMM TASK 71-00-00-710-009).
F 『 EEFF : ALL E ∞∞77-30-00∞∞∞∞∞∞∞∞∞∞Page 213
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 发动机指示(188)
